Go Back   PowerStrokeArmy > Non - Specific > Project Forum

Reply
 
Thread Tools Display Modes
  #1  
Old 09-15-2018, 01:45 AM
Darvis 6.0 Darvis 6.0 is offline
Private
Member's Gallery
 
Join Date: Aug 2018
Location: Oregon
Posts: 6
Default 6.0 swap into obs question.

I have a 96 obs that I put a 6.0 in, I made the harness standalone so no dash modules and extra junk, fires up runs great but goes into limp mode because of a vss code, it shifts flawless and speedo works in the transmission. Section on my scanner but not on live data, so about half a mile or so it derates fuel, still has good power but I need to figure out how to tell the computer it's getting a signal. So my question is, does anyone know these abs and vss wiring good enough to point me in the right direction? I've been messing with it so much on this one issue I parked the truck
  #2  
Old 09-15-2018, 12:30 PM
WILD_PHIL's Avatar
WILD_PHIL WILD_PHIL is offline
Major
Member's Gallery
 
Join Date: May 2012
Location: East TX
Posts: 2,377
Default

You should post this on compD and watch the damn heads explode. Lol Very interesting.


Sent from my iPhone using Tapatalk Pro
__________________
2009 F250 2WD CC
Family Wagon

13 Passat TDI SE 6MT

2005 F250 EC LWB 4X4 XL
Lifted, Customized, and DeStroked.
  #3  
Old 09-15-2018, 03:18 PM
co04cobra's Avatar
co04cobra co04cobra is offline
Sponsor
Member's Gallery
 
Join Date: May 2011
Location: WV
Posts: 2,815
Default

You should be able to tie into the factory obs rear abs sensor. Depending on which harness you used for taillights etc... you might have to tie into the VSS at the cluster. What Speedo did you use?


That’s a swap I have been interested in doing for years.
__________________
00 cc/sb zf6 F250- Some stuff done always more to do-Fuel 300/200s Air-Garrett 68/94-Oil SRP 1-Airdog to Fuellab

97 cc/sb- zf-5- Work in progress. PMF rsk w/ SD axles. 66 turbo, E fuel, 230/100s. SB DD clutch.

08 cc/sb - Elite bottom end - 2 fuelers, 59vgt/78atmo, Midwest 100% nozzles and coated heads etc....

www.teddavisautos.com

Many parts available for super duty trucks PM me.
  #4  
Old 09-19-2018, 11:31 AM
Darvis 6.0 Darvis 6.0 is offline
Private
Member's Gallery
 
Join Date: Aug 2018
Location: Oregon
Posts: 6
Default

I'm using the 96s complete factory harness and cluster, I just built the harness to run standalone, just needing input from the speed sensor to the pcm but I tried hooking the signal wire to the vss + on the pcm but still nothing,
  #5  
Old 09-19-2018, 09:24 PM
co04cobra's Avatar
co04cobra co04cobra is offline
Sponsor
Member's Gallery
 
Join Date: May 2011
Location: WV
Posts: 2,815
Default

Did you tie all the grounds together for your standalone? Only other thing I can think right now would be to separate that circuit if so and dedicate the ground just for it on the pcm side.


Speedo in the truck works fine? Sounds like a cool build. You should post up some pics when you get a chance.
__________________
00 cc/sb zf6 F250- Some stuff done always more to do-Fuel 300/200s Air-Garrett 68/94-Oil SRP 1-Airdog to Fuellab

97 cc/sb- zf-5- Work in progress. PMF rsk w/ SD axles. 66 turbo, E fuel, 230/100s. SB DD clutch.

08 cc/sb - Elite bottom end - 2 fuelers, 59vgt/78atmo, Midwest 100% nozzles and coated heads etc....

www.teddavisautos.com

Many parts available for super duty trucks PM me.
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 01:04 PM.

 

Powered by vBulletin®
Copyright ©2000 - 2018, vBulletin Solutions, Inc.

Designed by Military Ltd