#1
|
|||
|
|||
![]()
Does the 6.4 gear reduction starter work on a 6.0. Or can I just get a gear reduction starter ? I have had my truck for almost two years and not in goin on my third starter.
__________________
2006 6.0 Amarillo 37/13.5-r20 200,000km Sinister egr Cooler Airdog2 165gph 5 inch turbo back stainless exhaust |
#2
|
||||
|
||||
![]()
OEM they are both gear reduction the 6.4 is less of a reduction and spins faster
they both fit the 6.0 with no modification just FYI i pulled my 6.0 starter off and bolted on a used low mile Ebay 6.4 starter at 100,000 i have never had to replace a starter i just did it for the spin factor
__________________
DTR RON Huxell's Memorial donation page please donate https://www.gofundme.com/2464axqr |
#3
|
|||
|
|||
![]()
Thank you. Preferable brand by any chance ?
__________________
2006 6.0 Amarillo 37/13.5-r20 200,000km Sinister egr Cooler Airdog2 165gph 5 inch turbo back stainless exhaust |
#4
|
|||
|
|||
![]() Quote:
Same. I replaced my good OEM starter at 110k with a Bosch 6.4L starter. Starts much faster- dare I say almost as fast as a common rail...... ![]()
__________________
2005 6.0L ECSB S362 SXE /68/.91 -175/30's - Irate T4 - BPD FICM - BPD HD Cooler - BPD WP - ARP 4.30's - Yukon Locker - 35x12.5x18 - Bilstein 2.5 Kit - Trac. Bars NL CAI - ODP St3 Manifold - 4" Exhaust - CSF 6028 Edge CTS2 - SCT w/TSD tune - IDP FICM Tune - Jugger Pump w/Custom RR - Fuel Pressure Gauge CCV Mod - 2013 Bed/Gate - DC Power - Powerstops |
#5
|
|||
|
|||
![]()
I got my starter on tonight. And it starts much better. $240
__________________
2006 6.0 Amarillo 37/13.5-r20 200,000km Sinister egr Cooler Airdog2 165gph 5 inch turbo back stainless exhaust |
#6
|
||||
|
||||
![]()
Good to hear. I have gone backwards to get one running but didn't notice that it cranked slower. Wonder how it will do in the cold!!?
__________________
2017 F-350 DRW Platinum stock for now 1979 F-150 6.0 Swap in progress, 86mm LP turbo, 04 frame and interior |
#7
|
||||
|
||||
![]()
I hear the 6.7 starter is even better on these as it spins faster than the 6.4 starter.
It bolts right up also but.. it requires a bushing on the lower hole. https://www.youtube.com/watch?v=21Wq7CeOHk0 Found out while trying to figure out if a 6.7 starter worked on the 6.4. here is a huge thread over on fte on it with the starter specs 6.4 vs 6.7 vs 6.0 etc http://www.ford-trucks.com/forums/14...the-6-0-a.html
__________________
No Limit Fabrication Midwest Diesel & Auto Last edited by Powerstroke Man 6.4; 01-12-2017 at 02:43 AM. |
#8
|
||||
|
||||
![]() Quote:
__________________
2017 F-350 DRW Platinum stock for now 1979 F-150 6.0 Swap in progress, 86mm LP turbo, 04 frame and interior |
#9
|
||||
|
||||
![]() Quote:
__________________
2009 6.4 PSD, Motor built by Rudy's, Trans Built by Warren, 59/76, 60%, No Limit goodies, PMF suspension |
#10
|
|||
|
|||
![]()
We are supposed to get a cold snap up here in the next couple days so I will keep you guys updated ! Also that top bolt behind the cylinoid was a pain in the ass ! : D
__________________
2006 6.0 Amarillo 37/13.5-r20 200,000km Sinister egr Cooler Airdog2 165gph 5 inch turbo back stainless exhaust |
![]() |
Thread Tools | |
Display Modes | |
|
|