Honey badger Jr installed...

Been a few days, been busy as hell...

1800 miles on it since installed... What little smoke I had off idle is gone, ICP pressures remain the same, but the duty cycle is lower. I would expect with some tuning changes the ICP pressures could come up.

Seat of pants is about 20hp picked up with the chip on a mild econo tune.

Tony's tune I have is scary right now with the bottom end! LOL

No Limits tuning is spot on, needs some ICP added I think to feel the full effect.

Few pictures... Meant to get more but my phone died.

Nice Joe!

Looking at those pictures reminds me I need to clean up and fix up all the BS ****... I've got all kinds of clean up work to do....

How come you didn't go with the upgraded lines?

Later... Believe it or not these are my factory lines with 290k+ on them, thru 4 different motors and such...

Not broke, dont fix it... LOL

Understand that. I have mine all apart so seemed like as good time to upgrade.

Oh I'm sure they will blow tonight on the way to the RV thanks to you...










LOL

very nice joe. on another note, god those obs hpop res covers are UGLY imo! do you happen to know if the sd covers will bolt right up, provided you use the right gasket?

i don't see how your hobblin as$ could stand climbin up and down and layin across that engine

ghohouston said:

very nice joe. on another note, god those obs hpop res covers are UGLY imo! do you happen to know if the sd covers will bolt right up, provided you use the right gasket?

Click to expand...

Yes they will. If you have an OBS motor you can use the SD res, just use the non screened cover.

I like the OBS cover myself. I still have a RiffRaff res spacer I need to put on, but, and then I will polish the cover, but for now I like it.

bruce said:

i don't see how your hobblin as$ could stand climbin up and down and layin across that engine

Click to expand...

Thats what sucks these days with my new gimp leg... But I have a scaffold I carry with me all the time, best $60 bucks I have spent at HD... I have 3 at home and one in the RV at all times!

CSIPSD said:

Oh I'm sure they will blow tonight on the way to the RV thanks to you...










LOL

Click to expand...

I take it back!!!!! I take it all back:fustrate:

CSIPSD said:

Thats what sucks these days with my new gimp leg... But I have a scaffold I carry with me all the time, best $60 bucks I have spent at HD... I have 3 at home and one in the RV at all times!

Click to expand...

Looks good, I also noticed a difference with the adrenaline I put in. Pulls better up top
Also do you have a picture of said scaffold, I have been wanting to get one for a while now

Sent from my SAMSUNG-SGH-I537 using Tapatalk

Dmstrucks02 said:

Looks good, I also noticed a difference with the adrenaline I put in. Pulls better up top
Also do you have a picture of said scaffold, I have been wanting to get one for a while now

Sent from my SAMSUNG-SGH-I537 using Tapatalk

Click to expand...

There is a shot of one of them...

ohhh... a platform ladder. I thought you had some rolling scaffolding that you carried in the truck... and thought, damn that would take up the whole bed. haha

I want a topside creeper one of these days...

I need to replace my HPOP. Why did you go with the Honey Badger?

CSIPSD said:

There is a shot of one of them...

Click to expand...

Yea I have been looking at those online, I'm going to home Depot now to see if I can find one

Sent from my SAMSUNG-SGH-I537 using Tapatalk

Score $34 at HD

Sent from my SAMSUNG-SGH-I537 using Tapatalk

Dmstrucks02 said:

Score $34 at HD

Sent from my SAMSUNG-SGH-I537 using Tapatalk

Click to expand...

Love it! Its perfect for a 4-6" lift, I carry one everywhere.

Like I said I had been looking at them online but never thought to check HD or lowes
This was half the cost with no shipping

Sent from my SAMSUNG-SGH-I537 using Tapatalk

I have two of those and and the shop I do most of my work at has two more lol they're great