Recent content by atc500

Barder stage 2

SOLD Barder stage 2 built from a Powermax 64.7mm Compressor 66mm 10blade turbine fresh rebuild $900 located in Northern Utah
- atc500
- Thread
- Apr 12, 2023
- Replies: 0
- Forum: Aftermarket Performance
ICP V

Seems to pull pretty good on the race tune smoke isn’t much worse then my 175/30’s I had before but egts keep climbing my 175s would stop around 1450, I’ve noticed on the stock and tow tune it seems like it’s surging on the top end
- atc500
- Post #16
- Aug 16, 2021
- Forum: 6.0 Tech
ICP V

The ipr is maxing out 85%. The pump Is a New thumper II I’ve already been through my stock pump which held more Icp then the thumper I. Now I have a thumper II which is holding better Icp then the other two but it’s still not holding max Icp about 3400psi, the engine is calling for 3900+psi I’m...
- atc500
- Post #14
- Aug 15, 2021
- Forum: 6.0 Tech
ICP V

I replaced the nipple cups cause the had some wear at the ends and were loose there was no change in pressure after changing them and I’ve air tested it after with no leaks ipr % is maxed out I’ve also tried a new ipr with no change
- atc500
- Post #11
- Aug 15, 2021
- Forum: 6.0 Tech
ICP V

The truck starts and runs fine the issue i have is it’s not building full Icp at WOT it’s about 500psi low of desired which is why I believe it has a high pressure oil leak but it doesn’t show under normal 120psi shop air testing
- atc500
- Post #8
- Aug 15, 2021
- Forum: 6.0 Tech
ICP V
- atc500
- Post #5
- Aug 15, 2021
- Forum: 6.0 Tech
ICP V

I haven’t checked the psi on the stock tuning only voltage. I have WDI tunes so the Icp psi is fooled so it starts off around 1100psi at idle and only reads up to about 2300 wot
- atc500
- Post #4
- Aug 14, 2021
- Forum: 6.0 Tech
ICP V

Truck will not build over 4-4.13v Icp even on stock tune. It has a New Thumper II Hpop, 6month old Premium WDI 205/30 injectors, WDI high flow stand pipes and New nipple cups and o-rings. I’ve tried New Icp and ipr(motorcraft) it just stops and holds at 4-4.13v. I can run 120psi through the ipr...
- atc500
- Thread
- Aug 13, 2021
- Replies: 15
- Forum: 6.0 Tech
Rcd thumper Hpop

Who has any Real first hand experience with The RCD Thumper 1 Hpop? I put mine in about a week ago and it will only run 3.5-3.8v on a wot run my stock pump would bounce between 4-4.6v on the same WDI Race tune this is with 205/30 injectors, I’ve got WDI high flow stand pipes in it as well. I...
- atc500
- Thread
- Jun 10, 2021
- Replies: 1
- Forum: 6.0 Aftermarket
175/30 injectors 6.0

SOLD
- atc500
- Post #2
- Feb 10, 2021
- Forum: Aftermarket Performance
175/30 injectors 6.0

Ford 6.0 Warren 175/30 injectors about 30k miles they were remans with new spool valves when purchased zero issues with them just upgraded they will come with a Motorcraft o ring kit $1100 shipped No cores needed https://youtu.be/1nKLyhsVn7M Sent from my iPhone using Tapatalk
- atc500
- Thread
- Feb 4, 2021
- Replies: 1
- Forum: Aftermarket Performance
Injector rebuild questions?

You will save time and money just having a builder do them, for example $822 for a set from warrens with 6month warranty vs DIY $450 for stock nozzles alone plus whatever other parts you might need.
- atc500
- Post #4
- Sep 14, 2019
- Forum: 6.0 Tech
No limit cold side 6.0 pipe & Billet Zoodad plate/screen

Still have the plate? Sent from my iPhone using Tapatalk
- atc500
- Post #3
- Jun 26, 2019
- Forum: Aftermarket Performance
2007 F-350 Single cab 4x4 studded

SOLD
- atc500
- Post #4
- Mar 31, 2019
- Forum: Trucks
2007 F-350 Single cab 4x4 studded

Sorry I forgot price asking $10,800 currently had 186,600 miles located in northern Utah Sent from my iPhone using Tapatalk
- atc500
- Post #3
- Mar 23, 2019
- Forum: Trucks