Recent content by dbunyip

I'm stumped on a 03 no start

Well found a ficm I could steal and that wasn't it so out come the injectors. Only thing I can think of at this point.
- dbunyip
- Post #10
- Feb 3, 2015
- Forum: 6.0 Tech
I'm stumped on a 03 no start

I've been cranking on it for 2 weeks now, definitely more than it should take to bleed it. It will start on starting fluid but only runs for a few seconds. The injectors are from dr diesel or diesel dr. Something like that. My buddy got them. I always use full force but these were half the...
- dbunyip
- Post #7
- Jan 29, 2015
- Forum: 6.0 Tech
I'm stumped on a 03 no start

Working on an 03, did turbo, swapped to a ported 05 intake, Fuel banjo bolts, bulletproof EGR, HPOP, Glow plugs, all new o rings on the hpo lines and injectors and now it wont start. All the work was done as a P/M thing, nothing was wrong with the truck before the work. Other than PCM recalls...
- dbunyip
- Thread
- Jan 29, 2015
- Replies: 11
- Forum: 6.0 Tech
2008 FORD F250 4WD XLT, NO MOTOR/TRANS (POSSIBLE RACE TRUCK?) (4,700)

Any idea on how to/how much to shop to ca? I don't even know where to begin to do shipping on a truck
- dbunyip
- Post #19
- Jun 16, 2014
- Forum: Trucks
speedo not working

Did you get anywhere with this? My speedo quit working but my odometer still works. Any of these trucks get vss from front axle? I did a 05 axle swap but have not got the abs plugged in yet.
- dbunyip
- Post #13
- Nov 21, 2013
- Forum: 7.3 Tech
New daily driver build
- dbunyip
- Post #26
- Nov 4, 2013
- Forum: Project Forum
New daily driver build

Las time I seen it before it left for vegas. Can finally show off the one off stainless steel fusion bumper that took me 2 years to talk them into building I had bought the bed before the 13 conversion came into play. I have a full 08 front end it was supposed to go on it. Me and my body guy...
- dbunyip
- Post #25
- Nov 4, 2013
- Forum: Project Forum
New daily driver build

22x9 black fuel throttle on 35" toyos. Motor is all stock for now other than intake and exhaust
- dbunyip
- Post #19
- Oct 26, 2013
- Forum: Project Forum
New daily driver build

Ready to pick her up from the body shop now. Time to fit the fusion bumper and carli lift
- dbunyip
- Post #17
- Oct 25, 2013
- Forum: Project Forum
New daily driver build

Getting closer. Should be all bolted in place tomorrow ready for trim
- dbunyip
- Post #16
- Oct 22, 2013
- Forum: Project Forum
New daily driver build

Upper grill and hood latch adaptor parts
- dbunyip
- Post #15
- Oct 20, 2013
- Forum: Project Forum
New daily driver build

It's just sitting there loose but the best pic I have of the fender adaptor bracket
- dbunyip
- Post #14
- Oct 20, 2013
- Forum: Project Forum
New daily driver build

I'm not sure if it is available to the public yet, the kit I have is for test fitting but it comes from http://www.strikertrucks.com I'm not sure on what the pricing is yet, you will have to talk to them
- dbunyip
- Post #13
- Oct 20, 2013
- Forum: Project Forum
New daily driver build

One of the pieces I have been waiting on. Fiberglass wiper cowl as the oem setup does not fit remotely close to the older trucks or have a way to fasten. All smooth for a more custom look as well
- dbunyip
- Post #11
- Oct 20, 2013
- Forum: Project Forum
New daily driver build

Finally got to work on it some more and make some progress.
- dbunyip
- Post #10
- Oct 20, 2013
- Forum: Project Forum