Search results

  1. Stroked777

    08 crank no start

    Some times the fuel system can be a pain on these to bleed. Turn the key and push in the scherader valve on top of the fuel cooler in until straight fuel comes out. Air will tracks to the highest point it can and that's the highest point on the fuel system
  2. Stroked777

    Big Power 6.4 guys. Transmission ???

    If it was me (and it's my plan for my build) I would build that trans to hold as much as possible, billet everything, and upgraded disks. I plan on a goal of 800hp but I'm going to build my trans with every billet part I can
  3. Stroked777

    Injector pressure

    I remember talking to hassler about his common rail 7.3 and said he was running 50k?!? An that was 2 k16s and 6.4 injectors with machined plugs to fit in the head
  4. Stroked777

    2008 6.4 rear leaf spring bushing.

    Search for a spring shop near you. There was a place back where I use to live that could make any spring you want , thy did all the bending and everything in house, could just have them make a new top spring
  5. Stroked777

    (Insert cleaver build thread name here) Build Thread

    Didn't budget for a TC, I'll be getting one when I do my next phase and get trains parts and build my trans
  6. Stroked777

    Western NY

    What town
  7. Stroked777

    Up pipes blew with new turbos

    Up pipes can be done can on and transmission in, I don't have coolers so that makes it easier. I just removed my two piece down pipe and finagled all the pipes out where my down pipe was
  8. Stroked777

    (Insert cleaver build thread name here) Build Thread

    We will see how it works at 5200ft and above
  9. Stroked777

    (Insert cleaver build thread name here) Build Thread

    Hopefully soon I can tear into the motor I bought for 600 to see what else I'll need. All I'm waiting on is my friend to buy a house so I have a place to rebuild it LOL LOL. Atleast he closes on it I less than thirty days. I hope to have it running before winter
  10. Stroked777

    (Insert cleaver build thread name here) Build Thread

    Well found some wiggle room in the budget (aka talked to the fiancé and it was her idea) to get a billet single 66 from Midwest Diesel. So next time the truck is running it will be with a single
  11. Stroked777

    Western NY

    I lived near Albany before I moved out west, since carry concealed is out of the question for an out of state person, I would consider a bat or a big knife when in Albany. Place is sketchy as hell
  12. Stroked777

    crank case venting idea

    Tractor supply has a cheap strainer you can get, run the CCV into it and it has a catch can for it (with a little drain valve) and then run the other port back into the intake
  13. Stroked777

    Best programer for me?

    Mini max with ******** tunes. I seem to get the best mileage on my hottest tune
  14. Stroked777

    Shaking Trans?

    Check drive lines. Any u joint with play I would replace. Also give the carrier bearing a shake as well. Does the shake increase with engine rpm or road speed
  15. Stroked777

    Literature for engine rebuild?

    We have all data at work, would that have the info I need? I don't know if. I navigated it enough but I could never find specific info when ever I search. Also I would lik something portable, I'll be building my motor at my friends house, has to with a little item in the lease contract at my...
  16. Stroked777

    Literature for engine rebuild?

    Thanks man. As long as it's not over a hundred bucks lol
  17. Stroked777

    Literature for engine rebuild?

    Looking for a good shop manual to buy to rebuild my engine. Want a book that has procedures and specs and tolerances. Where can one find such a book. Thanks in advance
  18. Stroked777

    08 coolant leaking - dealer can't find

    Get coolers can be removed cab on. Just gotta remove the radiator I believe, that's if you wanna tackle it yourself, a dealer will lift the cab to make it easier
  19. Stroked777

    Tuning for a Cam

    Yeah I got it to run good after some emails with Matt, it was all about messing with the ebp tables and stuff, I was very happy with out it ran.... Now I need a new motor due to a lifter
  20. Stroked777

    (Insert cleaver build thread name here) Build Thread

    Sounds good sootie. New arps are good insurance I feel. Maybe I can sell my used set lol

Random media

2012-08-19_17-14-58_692
0102
IMG_8326
2013-01-06_17-11-35_447
22CFE362-8FC2-4A49-B36A-F2F44645DDFE
1995 f350
Doin It Daily Style...
Buster the wayward Boxer :)
2012-03-13_17-46-29_814
Tube_Tool
White truck
image335

Latest posts

Members online

Total: 854 (members: 2, guests: 852)
Top