Search results

My 02 Excursion is a limited with leather seats and the driver's side is memory, both of my front seats are getting rough, what it's the best option to replace or upgrade just the front two seats? Secondly, it has Factory fog lights, I was thinking the fog lights should come on when the marker...

I have a truck that I just did new lifters on, put it back together and everything is fine EXCEPT the reading for Pyro1 only reads 92 degrees all the time. Before doing the work it was working correctly. I have checked the user settings in the Mini maxx and it is set to use the factory pyro...

Had a truck brought to me that was popping out of the intake while running. Pulled the valve covers and a couple sets of rockers to inspect them and they were worn pretty well, so I replaced the rocker sets on both sides with new. Fired it up and ran fine for 10-12 miles then it developed a...

Does anyone have a place that you can get just that part, on the end of the fuel pick up in the tank?? I have 2 customers that need them and I haven't had any luck finding that. I hate to spend the money on the whole sending unit for just that little rubber piece. Thanks

I will be installing an 05 engine into an 03 truck, biggest thing is will the 05 engine wiring harness work? Only think I know of really that is out of place is the ICP sensor, that is why I was going to try and use the 05 harness since it came with the engine. Any other things that I need to...

Is it possible to disassemble the High pressure turbo and change the VGT actuator saft? A truck was brought to me that has it broken and the vanes stuck open.

1995 F250 Regular cab, Long bed 7.3 PSD, Automatic , 4x4. Odometer reads 173k miles but it didn't work for some time, it does work now, actual mileage is unknown though. Oxford white exterior with grey interior. The truck used to have a snow plow on it so it has quite a bit of rust. I will try...

I'm looking for the front case (with the bellhousing) for a ZF 6 speed for a 7.3. Got one I'm working on that the bellhousing is broken beyond repair. Thanks in advance

What would cause oil to mix into the coolant, Oil cooler obviously but is there anything else possible? What all is involved in doing an oil cooler on one these trucks? Thanks in advance

Got someone with an 02 automatic truck that the instrument cluster quit working on and his throttle response is down. Any thoughts on what it might be? It is located pretty far from me so I haven't actually gotten to look at it yet, but I'm trying to see if there's a common issue to look for so...

Like the title says, need a good working ZF6 six speed transmission for a 7.3 4x4 truck. The one I have has Low gear bad in it and stuck to the shaft. Located in Walton, KY 41094

InI was driving a friend's 2001 F350, I'm going down the interstate running 70-75 when it jerks like the engine hiccuped and lost power briefly while it made a quick screeching sound. So I start to get over and get off the highway when the screeching sound comes back again for about the same...

Need a good used PCM to replaced a VDH5 that is bad. DPC-462 It is for a 2002-2003 7.3 w/ Automatic trans. As soon as possible would be best. -Michael

This is my brother's truck he is selling: It is a Red '95 F350 Crew cab long bed. *It was an auto and he swapped it to a 5 speed, it has a South bend OFE clutch and the trans was gone through before the swap. *Has a 4" suspension lift with 35" tires, I would say the tires are currently 60%...

NVK4 for L99 to 01 auto - $300 PRY4 for '95 to 97 auto - $150 TEE4 for '95 to 97 auto - $250 Prices include shipping, The PRY4 is a reman.

I need the wiring harness for a 2001 7.3L truck with a ZF6 and manual shift transfer case, it comes from the driver side fenderwell down the frame to the crossmember. Need it ASAP -Michael

I'm looking for a 4 position switch for a Van Aaken chip for a 7.3. I have one here that is broken. Just the switch is all I need really -Michael

7.3L engine parts I have for sale: Cylinder heads $200 ea '95 HPOP w/ IPR $250 OBS turbo w/ pedistal and EBPV $350 OBS Exhaust manifolds $75 ea OBS Fuel bowl with factory lid $50 OBS mechanical fuel pump $40 Oil Cooler assembly $50 Harmonic Balancer $40 OBS turbo to intake Y-pipe $35 OBS/E99 2"...

Has anyone converted their truck from dual rear wheels to single rear wheels? I know the front axle has spacers that need removed to make the change but my concern is what is involved with the rear axle when keeping the Dana 80? I'm thinking it's wider but I'm not sure how much and if it would...

What is the piston protrusion suppose to be on a 7.3 . I have all the AERA specs, but it doesn't have a spec listed for this. -Michael