Search results

What would be needed if I turn my interior cab fire into a gutted essential only wiring. Just use it as a pulling truck. Used the truck for something else

Money is tight around my house plus COVID has made toilet paper hard to find. I really need this for my house. I believe it’s called “hit or miss toilet paper”. Does anybody have any sources? People who work sanitation, rest stops, county fairs, any place that deals with a lot TP. Shipping might...

So I got my 96 utility truck almost 2 weeks ago and now the gear shift is on the steering column. I thought ford did away with steering column shifting a long time ago. That was what....in the 70’s? So now whenever I get in the truck I got to go 1, then 2, then to a “D”? No 3,4, or 5? Not sure...

While driving up and down some mountains with no load, my engine oil ho”was getting “hot”. Close to 250. Not sure if my oil type is doing it. Schaffer’s 20w/50. “Not my normal oil”. With my dual IPR block, I could take the bleed off return line and out that oil through a oil cooler. Just a...

Not much going on, probably look dumb but oh well. When I start my truck after sitting overnight, itll run for about a second or two then die. Crank till oil refills and starts. After it starts, smokes bad. Gray smoke. My oil pressure is not what it should be. Getting the pressure at the Rez. 10...

Trying to see what else to check. Third brake light is working. It is aftermarket Got a new master brake sensor with the ford recall harness on it. Fuses are ok in that harness and under dash. I did get another clutch cutout switch. What do I need to check for at the steering wheel? Three...

Clutch slave cylinder mount broke and need the front case.

With my balanced engine, high rev valve springs and better valves, what would be a good max rpms be? 4000?

Not sure what is causing it. I am getting a CEL and will get it scanned ASAP. Thought I would let you guys see what I’m seeing. https://m.youtube.com/watch?v=KEy0XMZazGs

gwunter (Shannon) is the man. He took the task to design and fabricate a dual IPR block for me. I’m looking for advice as to how to plum the lines. Jason (Hot Rod Tractor) did his by taking a line coming from head into the input ports on each side of block. Then put the ICP sensor on the block...

Looking for some money, was informed it worked. $150.

Need the metal access cover that is on bottom of the trans. Mine is in bad shaped

Friend of mine got a 2012, he asked me if it was worth ******** the def. Figured I’d ask here.

Talked to my mechanic this evening and he's helping me with my P1211 code. (High/low ICP). He told me that with MY (not swamps) Gen 3 pump putting out more HPO than what the computer is used to seeing, I need to send my IDM in to a place that works on them and reprogram it to allow more HPO...

It is mechanical, just needed a 60 psi gauge. $40 obo.

My 40psi gauge isn't enough. Autometer would be fine. 2 1/16"

Radio on my piece of equipment has poor sound. Put in new radio, speakers and antenna. Didn't used to be this way. Has rodent damage. What would cause this? Bad ground? When I put in new radio, didn't change sound quality. Best way to describe how it sounds is like no base and have to turn...

Looks like I'll be assembling my motor myself. I'm gonna need any and all advice, tips and procedures about putting together my motor. First I'll be putting crank in. I can only do outside studs being that I got a girdle. The inner 2 will be in after Pistons are in.

For those who know my current predicament, I need my crank turned, new bearings, one new piston, lifters and cam need to be checked and new rings might be in order. Gonna need at least one new cometic head gasket also. It's not an expensive job, but gonna take some money. Machine shops around me...

Went smoothly. Didn't damage oil pan getting it off. But 3 jets were in the oil pan. Along with the freeze plug that I dropped also. I talked to Swamps, it is possible that the connecting rods may bump them. Wasn't aware of that. Was about 1000 or 2 miles that way. Was advised to check the...