Search results

  1. K

    No cruise control

    My truck is 2010 f250, fuel upgrades, nozzles, custom turbo setup etc. Running tunes from GH from way back. Truck just sits and collects dust mostly. Drive it once a year. Anyway no crusie control. Did the KOER switch test and nothing throws codes. Because the truck is modded it throws P179A and...
  2. K

    1996 tow rig upgrades??

    Hey it's been awhile since I've had my 7.3, had a 2000 truck that I built to 500 ish hp. Sold it mid 2000's. So I know a bit about building a 7.3 but I've been away from it for quite some time. I'm selling my current 2020 F350 6.7 as I've found a mint 7.3 to buy. Plan is to turn it into a bit of...
  3. K

    Will 37's fit??

    I have a 17 F350 with a 3.5" lift, on 20x10 rims with a -18 offset or 4.79 backspacing. Will 37's fit with this configuration? Thx.
  4. K

    Waste gate settings for a 35r and 4202r?

    I'm trying to figure out what I should have my gates set for. I have a gate to dump around the 35 to the 4202, and another gate to dump before the 4202 to the down pipe. The gate before the 35 is set at 20psi, and the gate before the 4202 set to 60psi. Good bad? More or less? I haven't messed...
  5. K

    4wd launch-Reduced power after engine oil level to high code?

    My truck has IDP tunes, different turbo setup, Industrial hpfp. Truck runs great other than it will throw the engine oil too high code and reduce power after I do a hard 4wd launch. Anyone run into this and find a solution? I've reloaded the tune and still happens. Any help is appreciated...
  6. K

    2016 w/2.5" level and bump steer??

    Just bought a '16, installed Ready lift 2.5" coils, radius arm drop brackets, and trac bar. Had some pretty good bump steer, so I then installed the trac relocation backet so the trac bar was paralell to the drag link, and it helped, but still have a fair bit of bump steer. Any ideas? Also...
  7. K

    Cylinder Head cracking and Intake Manifold!?

    What cylinders are cracking? All of them, randomly? Or is the ones closer to the firewall? Just wondering because of difference in flow in the intake. if so a ported intake should help? Also, can you get the no limits intake elbow that would work with a regular cold side pipe(so I wouldn't need...
  8. K

    Towing review w/ Spartan, Innovative, Hellwig products

    Installed a rear Hellwig sway bar and their LP-25 rear helper spring kit. My truck is a 2011 F250 with Icon 4.5" lift with no factory sway bar or overloads. I tow a tag behind triple axle, 24' trailer. The trailer has to be around 6-7000lbs. and my heavier skid steers are around 11,000lbs. I've...
  9. K

    Anyone use Hellwig products??

    Thinking about using their Load Pro helper springs and rear sway bar. Anyone have any experience with them? Kinda hoping the helper swigs would eliminate some of my axle rap too. Thanks.
  10. K

    Racin the 6.7 tomorrow w/Warhammer+Torq2!

    For those of you that have been to the track with one, what boost do you leave at? I'm gonna run the torq2 at 50% because that is the highest I can run it with losing the least amount rail pressure. Gonna drop some air in the tires. The truck has a 4.5" lift with 35's and 3.55 gear ratio, no...
  11. K

    Short review of Spartan 200hp Warhammer and Innovative torq2 stacked!

    So far so good. Noticeable difference. I'm running the torq2 at 100% with no codes and good power difference. Power comes on a lot sooner and the truck pulls harder and sounds throatier. I've towed 16,000lbs. with the knob at 50%. Not makin any recommendations here, just sayin I'm happy and it...
  12. K

    Crank case vent?

    Where is it? I'm lazy, don't wanna figure it out!!
  13. K

    Anyone running Spartan and Innovative Torq2?

    hows it workin? can they work together?
  14. K

    Precision turbo drop in for my gt4202r??

    Anyone familiar with Precision chime in please!! Is their a Precision turbo that would be a direct drop in for my gt4202r. My 42 has a vband outlet on the compressor as well as the inlet on the exhaust(Tial). I was thinking of a GTX4508r with a Tial 1.30 exhaust housing and a GTX42 compressor...
  15. K

    Changing turbos to Garret GTX/ need opinions

    Currently running a gt35r with tial stainless exhaust housing with a 1.03a/r and a gt4202r with tial 1.00 a/r. The truck spools uber quick but back pressure is to high on a full throttle run. I am changing the turbos out for a gtx3582r and a gtx4202r, I will stay with a 1.03 on the 35 as thart...
  16. K

    2011 Headlights??

    Anyone find any black aftermarket headlights yet? Thanks. __________________

Random media

step_12-3
tapatalk_1404232564793
HX40 map
The Truck
excursion_bumper
2005
2012-05-05_11-47-35_558
1908293_758548717501964_8276208862671434855_n
IMAG0255_1_
step_12
44485_1268371769888_1847662944_530825_6233400_n
6_4_coolant_line

Latest posts

Members online

Total: 386 (members: 2, guests: 384)
Top