Search results

  1. 96twofiddy

    96 misfire under load, help please

    Will do. Ill throw dielectric grease on all the connections just for giggles too. Also icp has oil in the connector, no code but I'm gonna replace it and see what happens.
  2. 96twofiddy

    96 misfire under load, help please

    Oh sorry I misunderstood. Lol makes sense. I butt connected them and heat shrinked them. Should I ditch the butt connectors? I had this problem before the harness too though
  3. 96twofiddy

    96 misfire under load, help please

    Also I replaces uvch on both sides but I used Dorman, truck had miss before and after. Maybe mis-shielded wires? Anyone had this problem?
  4. 96twofiddy

    96 misfire under load, help please

    Lol thanks. Well took out the chip and drove it. No codes on buzz test or cylinder contribution test. Koeo test good, koer test good. Icp voltage .9-1v at idle and ~600psi. No corrosion on pcm connector. So I'm thinking maybe mechanical problem with injectors maybe weak idm or a cylinder with...
  5. 96twofiddy

    96 misfire under load, help please

    Yea I kinda figured that could be an issue, but I am really hoping it isn't that lol. I will run a compression test at some point if it doesn't turn out to be an electrical issue.
  6. 96twofiddy

    96 misfire under load, help please

    disconnected chip, re connected and now it has 1,4,5,6,8 contribution/balance fault codes
  7. 96twofiddy

    96 misfire under load, help please

    Alrighty, so today I ran a cylinder contribution test, with the chip I got injector cylinder 1-8 contribution/balance fault. Ran koeo test, got code p0605 with the chip and p0603 without it. Also did the oil cooler because oil was coming out of it pretty good. Running another cylinder...
  8. 96twofiddy

    96 misfire under load, help please

    Haven't checked ipr and icp wiring very thoroughly, I had some bare wires on the cps, I heat shrinked and taped them up but I should really replace the pigtail. I will try to remember and check the other pigtails
  9. 96twofiddy

    96 misfire under load, help please

    How can you tell if is the cam walking forwards and backwards or the sensor? What kinda ohms should the sensor be? I didn't think it got better when I changed the sensor though but I will ohm it out to be sure.
  10. 96twofiddy

    96 misfire under load, help please

    Don't know what tuning, chip was on the truck when I got it. Yea I replaced the cam sensor after having it give me a no start problem.
  11. 96twofiddy

    96 misfire under load, help please

    Well I will have to try that. I was wondering if that coulda been a problem. But I didn't know if that was common or not.
  12. 96twofiddy

    96 misfire under load, help please

    It just rolled 304,000 Tuesday. I couldn't tell of they were new or original when I pulled the valve cover, everything looked really clean. Oh and I put in new glow plugs, don't think that would make a difference. Guess I should run a contribution test. But I kept getting an oil not up to temp...
  13. 96twofiddy

    96 misfire under load, help please

    I have a 96 7.3 5 speed with 6 position switch and exhaust but otherwise stock as far as I know. Under a load probably most prevalent with the trailer at about 1500 rpm or so until about 2000 rpm or so the truck bucks pretty bad like it has a misfire. Truck has done it for awhile. I replaced low...
  14. 96twofiddy

    OBS guys needing to Intercool! ATTN!!

    I would be interested in an aluminum one to put in my OBS, shipping to 78748???
  15. 96twofiddy

    97 Forged rod longblock

    Wish I wasn't so far, I could use a back up with 300k on the clock lol
  16. 96twofiddy

    What Do You Tow?

    May we know what you were hauling in there???
  17. 96twofiddy

    New from lake jackson,TX

    Welcome from Austin!
  18. 96twofiddy

    Stage 1 Injectors

    Idk about my HPOP but I just did my fuel pump and lines so at least that should be working well. I don't plan on getting greedy, safe and reliable power.
  19. 96twofiddy

    Towing with this safe?

    How much weight does he plan on towing? I personally wouldn't without any support under there. I would want at least a 1/4" plate sandwiching the sheet metal, minimum.
  20. 96twofiddy

    Stage 1 Injectors

    Wow. 326hp to the wheels is really good! Looks like I need to save my pennies and just get some lol. I tow my racecar to the track in 100+ degrees every other weekend 90mi each way, not super worried about having to watch egt's or some smoke, that doesn't bug me. I need it to be pretty darn...

Random media

1511MG-155
New Tires 3
for sale
0131
Spray adhesive that sticks to the rubber and plastic
gate_022
for sale
Interior
404497_3047082223674_457951947_n
IMG_0054
08 mirrors
IMG_22171

Latest posts

Members online

Total: 561 (members: 1, guests: 560)
Top