20x12 guys I need some help!

[Dakotakid]

06 f250, 1.5" level installed just put on my lt305/55r20s on 20x12 fuel octanes -44 offset and I rub(bad) I'm hitting my factory fender flare and not far behind that is my fender i don't know what to do, what have you guys trimmed?
Any help would be great

 

[O2ShootTheJ]

I took a set of shears and a hammer to mine on a 2.5in level and it only rubs a little now

 

[Dakotakid]

I took a set of shears and a hammer to mine on a 2.5in level and it only rubs a little now

That sounds terrible, but if that's what has to be done I guess I'll give it a try.
Have any pictures of what you cut?

 

[JMart]

06 f250, 1.5" level installed just put on my lt305/55r20s on 20x12 fuel octanes -44 offset and I rub(bad) I'm hitting my factory fender flare and not far behind that is my fender i don't know what to do, what have you guys trimmed?
Any help would be great

You have to much offset/wheel. You need to lift it higher to clear that, get different wheels, or turn less.

If you start trimming the fender flare, its going to start flopping in the wind. You could try a fender roller to roll the inside of the fender but if its hitting the outside, there isn't much you can do.

 

[Josh@DirtyDiesels]

I trimmed a little bit of my factory flare and into the fender with a grinder. You can barely see it. Next time I'm at the shop I'll take a pic. Truck is sitting torn apart now.

 

[HOOV3R]

Mine are modified a bit.

 

[Dakotakid]

I trimmed a little bit of my factory flare and into the fender with a grinder. You can barely see it. Next time I'm at the shop I'll take a pic. Truck is sitting torn apart now.

Thanks alot, you are exactly who i wanted to hear from, because your on 20x12s and 305/50s lowed, right?

 

[Dakotakid]

Here is how it sits now. Just got them on today.

 

[Josh@DirtyDiesels]

Thanks alot, you are exactly who i wanted to hear from, because your on 20x12s and 305/50s lowed, right?

yes. Truck literally sits on the bumpstops. Not really the easiest setup to fit LOL
It really didn't take too much trimming though.

 

[Dakotakid]

yes. Truck literally sits on the bumpstops. Not really the easiest setup to fit LOL
It really didn't take too much trimming though.

If you could get me some pictures that would be great, thanks alot.

 

[ford rules]

I did no trimming with mine, running 20x12 -44 with 305/50. Just had to pull the inner plastic fender liner back with a zip tie.

 

[O2ShootTheJ]

yea I looked at Josh's at MPD and he really didn't trim much at all. I need to push my fenders in a tiny bit more it rubs when i'm turning and unlevel or hit bumps

I'd take pics of mine, but i'm embarrassed by them lol. If a had a cutting wheel it would be pretty, but it looks like a 4 year old went at my fender liner lol. But I just took a chunk of the liner I cut off, put it on the bottom corner of the fender, and then hammer it back a little at a time. It rubs a little on the plastic piece under the bumper but I'm not worried about that

 

[Josh@DirtyDiesels]

yea I looked at Josh's at MPD and he really didn't trim much at all. I need to push my fenders in a tiny bit more it rubs when i'm turning and unlevel or hit bumps

I'd take pics of mine, but i'm embarrassed by them lol. If a had a cutting wheel it would be pretty, but it looks like a 4 year old went at my fender liner lol. But I just took a chunk of the liner I cut off, put it on the bottom corner of the fender, and then hammer it back a little at a time. It rubs a little on the plastic piece under the bumper but I'm not worried about that

Looked at my fenders but didn't come say hi.... damn kid!

 

[O2ShootTheJ]

I didn't know what you looked like. Guess I should have stalked your facebook first LOL

 

[Dakotakid]

yea I looked at Josh's at MPD and he really didn't trim much at all. I need to push my fenders in a tiny bit more it rubs when i'm turning and unlevel or hit bumps

I'd take pics of mine, but i'm embarrassed by them lol. If a had a cutting wheel it would be pretty, but it looks like a 4 year old went at my fender liner lol. But I just took a chunk of the liner I cut off, put it on the bottom corner of the fender, and then hammer it back a little at a time. It rubs a little on the plastic piece under the bumper but I'm not worried about that

post up some pics, i wont judge. I just want mine to clear, im worried about ripping off my fender flare.

 

[07powerstroke91]

Good luck man, having the factory flares makes it even harder to get away without rubbing. I had 33's and 20x12 with a 2.5" level and trimmed a good bit, it still rubbed a lot. Ended up getting a 4.5" lift

 

[Josh@DirtyDiesels]

I didn't know what you looked like. Guess I should have stalked your facebook first LOL

LOL that's the name of the game. I was under the tent selling DD shirts and hanging with my gf and Carly all day ha

 

[O2ShootTheJ]

post up some pics, i wont judge. I just want mine to clear, im worried about ripping off my fender flare.

I'll grab a few in the sunlight tomorrow.

 

[O2ShootTheJ]

 

[Dakotakid]

thanks for the pictures, good looking pickup