Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
New showcase items
New showcase comments
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Showcase
New items
New comments
Latest content
Latest reviews
Latest updates
Search showcase
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Power Strokes
7.3 Tech
No HPOP pressure
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
[QUOTE="haligen, post: 1509119, member: 19816"] Ok, so I've been trying for several weeks in vain to get this fixed. To begin with the problem started shortly after changing the injectors. I had some hybrids that were not playing nicely with my tuning and decided to pull them out until I could get them looked at. I installed the stock injectors with new o-rings and washers. The truck started up and was running pretty good. I was planning on leaving for a camping trip the next day so I took it out to run it fairly hard in hopes of getting all the air worked out. About 15 mins into the ride I punched the throttle and heard a pop, the motor shut down like a bad CPS. Trying to restart it I had RPMs when cranking but was making no high pressure oil (I have a DP tuner infinity), duty cycle was at 54%. Had it strapped to a friends house and started looking at things. Disconnected the ICP sensor, still no start Removed and checked every injector, all o-rings where good and the injectors were firmly seated. No oil was coming out of a spout so I assume no stuck poppets Changed to another IPR, got it to run but then immediately died if you put it in drive. Swapped the old one back in, same thing Changed the CPS for the hell of it with a NAPA Echlin Checked the oil filter relief valve (or whatever its called under the filter) was still in place. Had a melling LPOP that I had been meaning to install, still no difference, reservoir always had oil in it when I pulled the plug. Changed the HPOP, it ran for a little while but once warm died and wouldn't restart till it cooled down Installed a new motorcraft IPR Finally started building high pressure oil, got the truck started and took it for a decent ride. The whole time I was driving it I had a decent amount of smoke coming out of the tail pipe and a good bit of smoke coming out of the crank case vent (figured it was from the oil that had collected in the cylinders and exhaust from changing the injectors). Since I had been messing around under the valve covers I had only put a few bolts back in to hold them on while testing. During which I somehow blew almost all the oil out of the drivers side valve cover and caused the truck to shut down. The whole side of the truck and underside were coated in oil. I refilled the oil and have yet to get the truck to start. Thinking I might have had a leak in the heads and to rule out the pump I deadheaded it and got an adapter to use a spare ICP sensor to check pressure. At 54% duty cycle and a good bit of cranking I max out at around 115psi. Probably this LPOP pressure but haven't confirmed. A second pump acts the same way. At this point I'm lost as to where to go next. I know the HPOP gear is engaged, I have the right gasket style for the pump, the bolt is tight, and the reservoir has oil in it. I should be making at least some pressure I would think. Any help as to what I could be overlooking would be wonderful. Current mods and replaced parts: New head gaskets with ARP studs, Comp Cam springs, and new injector cups. KC38R turbo E-fuel all oil galley plugs replaced (internal and external) oil cooler rebuilt EBP valve removed Melling LPOP PHP Hydra, but running stock tune while trying to sort this mess out BTS Trans Mishimoto Radiator Upgraded to Super Duty UVCH Modded IDM and probably other stuff I'm forgetting [/QUOTE]
Insert quotes…
Verification
Post reply
Random media
Latest posts
New torque converter locking up in Reverse and 1st gear
Latest: gahm3r
Yesterday at 4:16 PM
6.4 Tech
0
Dana 80 cab and chassis rear end
Latest: 03f3507.3
Yesterday at 2:11 PM
Engine and Drivetrain
Another jack of all trades tire thread
Latest: ToMang07
Yesterday at 7:28 AM
Suspension, Drive Train, and Tires
B
No Start help
Latest: bismic
Yesterday at 7:04 AM
6.0 Tech
Compound Turbocharged 6.0L Powerstroke Engine
Latest: 6.0 Tech
Wednesday at 8:24 AM
Ford Power Stroke News
Members online
No members online now.
Forums
Power Strokes
7.3 Tech
No HPOP pressure
Top