Recent content by Klutch

  1. K

    No cruise control

    Ok thanks, I figured it was something like that.
  2. K

    No cruise control

    My truck is 2010 f250, fuel upgrades, nozzles, custom turbo setup etc. Running tunes from GH from way back. Truck just sits and collects dust mostly. Drive it once a year. Anyway no crusie control. Did the KOER switch test and nothing throws codes. Because the truck is modded it throws P179A and...
  3. K

    1996 tow rig upgrades??

    Cool, which thread are you referring to?
  4. K

    1996 tow rig upgrades??

    Hey it's been awhile since I've had my 7.3, had a 2000 truck that I built to 500 ish hp. Sold it mid 2000's. So I know a bit about building a 7.3 but I've been away from it for quite some time. I'm selling my current 2020 F350 6.7 as I've found a mint 7.3 to buy. Plan is to turn it into a bit of...
  5. K

    Will 37's fit??

    Deadly, ur truck looks good. What tires r those?
  6. K

    Will 37's fit??

    I have a 17 F350 with a 3.5" lift, on 20x10 rims with a -18 offset or 4.79 backspacing. Will 37's fit with this configuration? Thx.
  7. K

    Waste gate settings for a 35r and 4202r?

    For bp, did you tee off somehow off the factory bp location? Gotta say, today was the first day running the GH tunes, and it ran pretty hard! Sent from my Nexus 6P using Tapatalk
  8. K

    Waste gate settings for a 35r and 4202r?

    Yes gotcha. I just checked you're right. Exhaust is psia. You can get both on on boost tho. My 72psi boost reading is from my waste gate controller. So it is psig. Seems like the dash daq stops reading at 87 on the exhaust. So not real sure what bp is. Could be higher. I guess I could keep...
  9. K

    Waste gate settings for a 35r and 4202r?

    Yes that's right total. Makes sense. I'll see about adding a gauge after primary. I'll check the dash daq as well. What does absolute tell me other than adding atmosphere to gauge pressure ? Sent from my Nexus 6P using Tapatalk
  10. K

    Waste gate settings for a 35r and 4202r?

    Just took it for a rip. Max boost is about 72psi. Back pressure reads 87, but either the factory pressure sensor only reads to 87 or it's the dash daq I use for monitoring. So should I be pushing the 4202 up to 72psi or should I back it off?
  11. K

    Waste gate settings for a 35r and 4202r?

    My 4202 has a 1.00 A/R Tial housing..
  12. K

    Waste gate settings for a 35r and 4202r?

    I can watch back pressure to set the gate to dump into down pipe(dump around the 42). To set the gate on the 35 might be tough using back pressure to get an idea, wouldn't it? I gotta think on that one..
  13. K

    Waste gate settings for a 35r and 4202r?

    No spray. Dragonfire single pump with 75% nozzles. I'm aware the nozzles are large for that pump, but that's what I have. What ya think on the 35, in the 30psi range? If the 4202 can get up to 60psi with this setup, what should I set it for? What is a good back pressure ratio? Thx.
  14. K

    Waste gate settings for a 35r and 4202r?

    I'm trying to figure out what I should have my gates set for. I have a gate to dump around the 35 to the 4202, and another gate to dump before the 4202 to the down pipe. The gate before the 35 is set at 20psi, and the gate before the 4202 set to 60psi. Good bad? More or less? I haven't messed...
  15. K

    4wd launch-Reduced power after engine oil level to high code?

    Cool, thx guys.
See more

Random media

The Truck
0251
led_tail_3
2008 6.4L pic10
IMG_20111009_185528
IMG_20130417_153401_644
g353
tran_720110116135837
IMG_20120106_133328
20220319_092724.jpg
DSC01424
DSC01413

Latest posts

Members online

Total: 900 (members: 3, guests: 897)
Top