Search results
-
Keeps blowing injectors
I tried to resize that picture ^^, but it's not working with photobucket IDK??- Gary
- Post #31
- Forum: 6.0 Aftermarket
-
Best stock 6.0 injectors for the $
Is the software a yearly subscription? -
Best stock 6.0 injectors for the $
So how would you compare a Snap on scanner to a IDS? I may have to buy me a IDS. -
Keeps blowing injectors
This is what low fuel pressure causes That top backer ring was probably cracked by the guys that put those top injector seals in, I'll bet they were fighting the snap ring and cracked it, then reused it. Those backer rings don't just fail.- Gary
- Post #30
- Forum: 6.0 Aftermarket
-
Best stock 6.0 injectors for the $
I've been using this tester for about 5 years, it's been on 100's of trucks, I also use a Snap On Modis that has cylinder/power balance. The G2 will condemn a injector with >350ms (milli sec) of stiction, you will never see that in a cylinder balance test, NEVER. So, on a cold start you have... -
Best stock 6.0 injectors for the $
Actually I have tried hot shots, the results vary. It can and does help/work but it's not a cure, I'd call it a band-aid at best. You may not notice a instance improvement, but over some time it will help. I have even tried to polish the spool valves, and I could see a big difference at a idle... -
Best stock 6.0 injectors for the $
Looks like your in NC, so you don't see the cold we see here in the North. The colder it gets, the worse the stiction is. I've tested a lot of engine stone cold, that's where stiction is at it's worst. If you start a cold engine and watch the tester for stiction values they will start to... -
Best stock 6.0 injectors for the $
^^^ That explains it all ^^^ Anything else is JUNK period, and if you tested them with a Hickok G2 tester you could see the difference. -
Best stock 6.0 injectors for the $
Here is a picture from a aftermarket injector problem from this week, somebody else put it in and it was at a friends shop. -
Best stock 6.0 injectors for the $
I seen a video that was produced by Ford, and the Motorcraft injectors have a updated set of coils, new spool valve, harness and connector. Now the new coils have a relief on the side the faces the spool valve, that is to to help ex-spell oil which helps to prevent stiction. I avoid all... -
-
Best stock 6.0 injectors for the $
No I haven't, The company that I said 7 out of 8 failed, they told me that all Motorcraft injectors were done by them LOLLOLLOLLOL, pure BS. So after the injectors were in the engine and it actually ran worse with their injectors than the original 200k mile injectors I called their tech guy... -
Best stock 6.0 injectors for the $
I don't believe there is a aftermarket injector that can compare to a Motorcraft, After using the Hickok G2 tester for probably 5 years now I call aftermarket injectors junk. Anybody that works on 6.0 really needs that tester, you can get to the bottom of a injector issue in minutes, with 100%... -
Best stock 6.0 injectors for the $
That's with a exchange. I see a lot of guys talk about a Ford dealer (Sunrise Ford?) that sells to the general public for a discount, I would try them, I'll bet they give you a good price. -
Best stock 6.0 injectors for the $
I don't want to post the name in public, but I'll say this, I have not found any aftermarket 6.0 injectors that last even after they work from the start. Then on the other hand after using 100's and 100's of Motorcraft injectors I had 1 fail and it had 10k miles on it. So to me the math is... -
cylinder balance rates
A cylinder balance test is only accurate at a idle or fixed RPM, if you have control of the throttle, and are working it how could it accurately measure? -
Best stock 6.0 injectors for the $
The BEST quality injectors are Motorcraft. I have a Hickok G2 tester (check it out on youtube) and have been using it for years to test these trucks for years, the tester don't lie! The 6.0 engine runs sooooo nice when it doesn't have a stiction issue. A new Motorcraft will have 245-255ms delay... -
Hpo issue?
I had one that had the same problem like you described, the guy installed the updated STC fitting upside down. -
a/c gurus
It's either overcharged or the condenser is not doing it job. If the condenser fins are cover with debris or full of dead bugs air can't get through it to properly cool it, when that happens head pressure goes up, and it can go way up. So the first thing to do is a through cleaning of the... -
Barometer question
The baro sensor is under the dash near the steering column, is that what you changed? What did you see for Hz? and what is you altitude? I'm at 900ft and see 155-158hz on most vehicles.
