Search results
-
7.3 Oil galley plugs
Size? I don’t know. What I can is provide you with a link to them. http://www.riffraffdiesel.com/cylinder-head-oil-rail-end-plug/ —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:... -
LPOP exploded, anyone see this happen before?
What were you doing at 140mph? Is this a built motor? 4500rpm is crazy high. Even at the speed something isn’t right though. —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:... -
LPOP exploded, anyone see this happen before?
Nope can’t say that I have. Looks dry or is that brake cleaner you used on it? Riffraff would be a good new replacement. —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:... -
Time to do injectors
Looks good! —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:...- DieselDC
- Post #75
- Forum: 7.3 Aftermarket
-
Time to do injectors
Haha that’s why i say to lock up the crank pulley with a breaker bar and then snug it in to the hpop to 98 ft/lbs. Just make damn sure the gear is aligned with the hpop else it won’t be spinning squat. If you need to remove the crank pulley, same procedure with the breaker bar. Then go inside...- DieselDC
- Post #72
- Forum: 7.3 Aftermarket
-
Time to do injectors
One last tip b4 wife grabs my phone.... brace your breaker bar on the steering armatures to lock crank pulley in place while you torque the hpop bolt. —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:...- DieselDC
- Post #68
- Forum: 7.3 Aftermarket
-
Time to do injectors
I don’t know I’ve always used the 3/16 plug on top to fill it. Fckker is so damn small I have a specific jb welded funnel made for it b/c I’ve changed out a few many hpops. —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:...- DieselDC
- Post #67
- Forum: 7.3 Aftermarket
-
Time to do injectors
Iirc Bob from dieselsite says if you can’t torque the nut down, torque it down till she spins the motor and you’re gtg. —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:...- DieselDC
- Post #64
- Forum: 7.3 Aftermarket
-
Time to do injectors
Yup and yup. You can crank till pigs [emoji241] fly and it will never start if that bolt isn’t on the hpop —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:...- DieselDC
- Post #62
- Forum: 7.3 Aftermarket
-
Time to do injectors
Your truck started b4 all this so it’s nothing to do with ipr, icp etc - or so im lead to believe... Okay just for chits... plug in your reader and let’s see what you got for ipr and icp. Icp at 100 and bouncing, ipr under 50. If icp is not at least 100, your pump may be installed incorrectly...- DieselDC
- Post #59
- Forum: 7.3 Aftermarket
-
Time to do injectors
Lol @79jasper at it again making sure you dot your T and cross your I [emoji13] —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:...- DieselDC
- Post #56
- Forum: 7.3 Aftermarket
-
Time to do injectors
That might have been a bad idea with the 2000grit. Could have got into ipr and sand, oil, injectors might not be a good mix. I think you’ll be alright. If the ipr, cps wasn’t problematic prior, you should have no other problems starting up the beast. —————signature————— ~Don’t overthink...- DieselDC
- Post #53
- Forum: 7.3 Aftermarket
-
Time to do injectors
Your truck will start without the chip no problem. Just don’t try to drive with it... With that said... you need to connect the chip to your laptop and transfer the tunes over. Then install the chip onto the pcm (batteries unplugged). Prior to cranking - did you pour oil into the hpop? That...- DieselDC
- Post #49
- Forum: 7.3 Aftermarket
-
Wet passengers side floor
All are plastic over metal sub framing . —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:... -
Wet passengers side floor
All four of my 7.3 leak from the windshield. Ford suck at windshield installs from the factory. Catch it early so it doesn’t rust. Have it resealed if no rust. —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:... -
BTS 4r100 and S468
either way you look at it is a loss. You either buy it or you don’t. So throw him a figure b/c I think it’s a good deal. I would buy it just as is and have it tig welded by a pro (who will probably charge you $120 an hour). I don’t think it’s going to come apart when installed. These are the...- DieselDC
- Post #8
- Forum: Engine and Drivetrain
-
please help 7.3 problems
Dammit no like button... #like —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:... -
please help 7.3 problems
Exactly so... best thing would be custom tunes. At least it’s not 100 cookie cutter files like what hydra has on their server. Tuner can at least change here and there based on knowledge/experience of live tuning. —————signature————— ~Don’t overthink something simple~ ...:uptight people... -
please help 7.3 problems
Not everyone can have it lived tuned. Custom tunes would be your best bet. —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:... -
please help 7.3 problems
Canned tunes. —————signature————— ~Don’t overthink something simple~ ...:uptight people suck:...
Members online
No members online now.