Search results
-
2020 revealed
Yep I priced out the truck I want looks like a 4K increase. Getting ready to order a F450 XL CC 4x4 in velocity blue.- superpsd
- Post #68
- Forum: 2017+ 6.7 Aluminum Super Duty
-
2020 revealed
Says 6 speed Torqshift (NA F250 6.2) 6 speed Torqshift G (F250 6.2) 10 speed torqshift (NA 6.2 F250) And under axle ratio availability it appears you can only order a 6 speed if it is coupled to a 6.2 if you buy a 7. 3 or 6.7 it is 10 speed standard. Under optional equiptment it does show an...- superpsd
- Post #66
- Forum: 2017+ 6.7 Aluminum Super Duty
-
2020 revealed
The original documentation I had seen had mid November as the beginning build date. Did they mention what the current build date is?- superpsd
- Post #64
- Forum: 2017+ 6.7 Aluminum Super Duty
-
2020 revealed
Huh my dealer told me 22nd. How the heck did you order one when the full spec numbers are not even released and or there is not yet an option to build on the website?- superpsd
- Post #62
- Forum: 2017+ 6.7 Aluminum Super Duty
-
2020 revealed
Stopped by the dealership today. He saif the ordering banks have been pushed to the 22nd.- superpsd
- Post #59
- Forum: 2017+ 6.7 Aluminum Super Duty
-
Fresh build dies after warm up
Tempature related seems like oil is bleeding off but it could be another issue. I would unplug an injector at a time and see if anything changes. -
Fresh build dies after warm up
Along with using a meter to verify voltage also look at the PID to see what the PCM voltage is seeing. Do you still have yout old IPR or another IPR to swap in? Even a ford/motorcraft part could be defective out of the box. -
2020 revealed
https://jalopnik.com/why-the-ford-super-duty-s-7-3-liter-v8-makes-only-430-h-1836880836/amp 7.3 will be 430/475trq and 350/468trq for chassis cabs.- superpsd
- Post #56
- Forum: 2017+ 6.7 Aluminum Super Duty
-
ZF6 Build
ZF5 manual with 3.55s. The injectors are some B codes I built not hybrids. My setup is substantial different but works for me. The engine is untouched. Just a forged rod motor with 300K miles. No studs, springs, etc... I am not using the full potential of the injectors as I use the truck these...- superpsd
- Post #25
- Forum: 7.3 Aftermarket
-
ZF6 Build
Also If you were to go 364.5 I would stick with the larger turbine as it will of course bolt right in. I wouldn't use the smaller turbine size on a 7.3.- superpsd
- Post #23
- Forum: 7.3 Aftermarket
-
ZF6 Build
First of all 80% or 200% nozzles with GOOD tuning may be cleaner and cooler running than a 100% nozzle. 80% and 200% nozzles are EDM nozzles where as the 100s start as 80s and Extrude honing is used to get them to the 100% size. In theory the EH nozzles are dirtier than EDM nozzles. I say in...- superpsd
- Post #22
- Forum: 7.3 Aftermarket
-
2020 revealed
The new trucks are getting on board wifi? What I originally read is wifi was going to be standard on all models except optional oj XLs. The 2020 explorers have a center sharp fin which I assume is the antenna.- superpsd
- Post #55
- Forum: 2017+ 6.7 Aluminum Super Duty
-
Tuners
Selling a 7.3 leaves a empty spot in your heart and leads to purchasing another...- superpsd
- Post #24
- Forum: 7.3 Aftermarket
-
2020 revealed
This EPA naughty list is growing all the time. I see where there is now a larger push for intact tuning and Carb Approved tuning.- superpsd
- Post #52
- Forum: 2017+ 6.7 Aluminum Super Duty
-
2015 vs 2020
There have been plenty of failed 10 speeds so far but its natural first years of the design to work out the bugs in the hardware and software. They did say in an article I read the 2020 superduty has been the most tested superduty to date with most miles logged. Ordering bank is open 8/14 and...- superpsd
- Post #58
- Forum: 2017+ 6.7 Aluminum Super Duty
-
New injectors and now sputtering at or above 2500 rpm
It is typical to see higher temps under heavier load like climbing a hill even with no payload. Get an actual EGT probe to monitor EGTs if concerned. Or get a scan tool to watch EOT thru the OBD port as EOT is usually with in a few degrees of coolant temp. If your coolant temp gauge is in the...- superpsd
- Post #52
- Forum: 94-97 Tech
-
Tuners
1023 was started bt Dusty Hogate. He has been on other forums. They are in Alaska. I've seen mixed comments and reviews.- superpsd
- Post #9
- Forum: 7.3 Aftermarket
-
Tuners
Most are legit tuners. Quite a few new names but many have been in the game for a while. The older tuners are still around as well like PHP, DP, Geerhead etc. Some of the newer tuning options I see thrown around are Jeli built, (Brian Jelich a familiar name) SDK performance (Dan K), 1023 diesel...- superpsd
- Post #2
- Forum: 7.3 Aftermarket
-
New injectors and now sputtering at or above 2500 rpm
Actual Dsberman94 was first to mention it to be fair. Welcome.- superpsd
- Post #41
- Forum: 94-97 Tech
-
2015 vs 2020
Well I'm still going to roll the dice it will be under warranty and I have other trucks if it were to end up back at the dealership often.- superpsd
- Post #47
- Forum: 2017+ 6.7 Aluminum Super Duty
