Search results

Ok this one is for the wire gurus. I’ve purchased an OBD2 Bluetooth connector Lelink for iOS iPad/iPhone. I’ve downloaded 3 apps,engine link,OBD fusion,OBD evolution. All of the apps connects to device but not the pcm. It does fine on my 96 Chevy s10. I’ve taken the connector loose from under...

After @350k miles the injector orings have failed and possibly the injectors themselves. Oil in the fuel and running really rough. I’m wanting a little more power but not not to hit 500hp yet because I’m not ready to pull heads and do studs and valves. And I just purchased a new kc turbo stage 1...

Well I just got it out of the shop to what was the idm relay and some bent pcm pins. Then I had to get the upipes sealed off behind the turbo and found the map sensor to be bad. Since I got it running Friday night wth turbo making boost it felt like it was struggling to get fuel. Still the turbo...

Starting a new thread here from IDM,PCM no start. So I finally got my truck back on Friday. The mechanic fixed my no start issue just as I asked him to. So I get in and take off and No Turbo Boost. I had installed a new turbo from KC Turbo(stage 1 with 66/88 stock exhaust housing) and new...

I don’t have any experience with a 7.3 in front of a zig 6 speed. I’m looking at 2 trucks both are 7.3 F-350 srw/4wd with 373 gears. One is a cc/lb the other is a reg cab/lb. Both are pretty much stock. The reg cab has a different exhaust with a muffler,ts 6 chip and gauges that’s it far as I...

I just test drive a 2011 F-350 DRW 69k miles. It has h&s tuner no limit egr,def ****** kit mpd piping in red coating and think it's a hxe turbo with 5" exhaust. Sounds really good and has a nice whistle. I'm not too familiar with the 6.7's. I've read about turbo issues and cooling problems. It...

I was on my way home from Charleston SC early Friday morning and my engine pulsed off and on a couple times. This happened once before and one of the wires had rubbed a bare spot arcing out on the fuel line. I stopped checked it out looked ok went on. After I got home I had the hood up while...

So the other day I get in crank up my truck and take off down the road. When hit the pedal to take off it was knocking with no power. Checked oil and it was 4 quarts low. The motor has @320k miles on it and it's been @2000 miles since last oil change. I run 15/40 chevron delo and motor craft oil...

So I got new stickers for my truck and she's riding like new again. However the mechanic said that 3 of my wheels were not true. He did get them balanced out just a little more weight than he likes. Couple days later I got to noticing a slight vibration when coasting off the throttle which felt...

Have a friend in the Southeast part of North Carolina. They have an 05,6.0 that has a cracked head. Truck is mint condition with just over 200k. Would it be best to have the engine fixed or have one built and bulletproofed ready to go? They've been quoted 7000$ just to replace the heads.

I was watching a you tube video comparing hp to the rear wheels for the 3 1 ton trucks. Ford Dodge and Chevy. Ford was putting down somewhere around 40 more hp than dodge and Chevy wasn't in the ballpark. However Dodge had around 18 more ft/lbs of torque. Here in the near future I'm planning to...

This has happened several times. After someone works on my truck or even me the calipers will loosen. I use thread lock and torque down to spec. What is doing this?

Well guys I'm going to have to replace my up pipes and rebuild the stock turbo. I wanted to go with a t4 setup but with other issues can't afford right now. There's some rebuild kits on eBay with 360 ball bearing 66/88mm .94 ar ported housing for @250-450$. I'm sure I'll have to at least get...

Ok I've been dealing wirh this issue for quite a while now. The rear end was acting as if I had a bent rim. Like a wobble. Changed tires,rims,rotors,pads,new caliper,new tires. All the universals I n the drive shaft have been changed,even in the front drive shat from the transfer case. The...

Ok guys I could use a lil help here. I just bought a matching pcm for my truck. Is it ok to just go ahead and plug it in or is there any type of programming to be done? The guy I bought it from said it never had a chip or Programmer hooked up to it. And all the numbers match.

Okay I'm transferring this topic from anyone ther thread and hopefully someone can at very least make some sense. All this happened after I plugged in an edge Evo tuner into my truck that was programmed for a manual transmission. Edge sent a Programmer to put my info back on my pcm and...

I've mensioned this on another thread and read all over about different ways to diagnose my issue. I've tried the self test and I can't get the cruise light to even blink once. I tried putting a jumper in the brake pressure switch and now I've just tied them together. Took instrument panel out...

Ok tuning experts! I'm needing my PCM flashed and have called Ford and several other mechanics in the area and they all need my truck in order to do this. However the tuning guys just need the PCM. My truck is in the shop now and the guy calls and says he can't reflash it because there is a bad...

2000 f350 6speed man,Ext cab with welding bed. New 7.3 from Ford,new rebuilt reared. 300k on the truck. Semi rims. Welding bed is going to repainted. I only one pic. A friend of mine husband passed and he was an Iraq veteran in the US Army. She would like to sell this truck and a Lincoln...

I'm going to install new brake pads on my 01 F250 this morning. When I did the seals in the axle and hub I must've got something wrong when I put it back together. My abs light stays on and it's not working right. Sometimes when I push down on the brakes the back ones lock up. ANy ideas on how...