Search results
-
S
Iso rear center seat belt cc
Id like it to be tan, not sure why mines missing thanks anyways ttt- Stroked
- Post #3
- Forum: Interior Parts
-
S
Iso rear center seat belt cc
In search of rear center seat belt for my tan 01 lariat crew cab. Bolts and all, lemme know what youve got- Stroked
- Thread
- Replies: 3
- Forum: Interior Parts
-
S
2002 Crew Lariat Interior
Pm'd about rear seat cupholders and rear seat center seatbelt- Stroked
- Post #27
- Forum: Interior Parts
-
S
Who has the best single shot injectors with tunes?
swamps, and swamps... swamps injectors are great with their tuning, and gearhead tuning is great as well. proven time and time again- Stroked
- Post #9
- Forum: 7.3 Aftermarket
-
S
battery terminal corroson ??
coke will do the same job as baking soda, if you were in a pinch. and yeaa, get those replaced and have your batteries tested. Cold weather and dead batteries are bad news, good way to ruin them. its all about the maintenance -
S
Low coolant possible bad head gasket?
as said, check the code, but theres usually not a code for a coolant leak,... also see if someone near you can possibly do a a compression test for you. guessing through the internet is a good start, but youll never figure it out until you check the obvious -
S
bellowed uppipes
dont try to cut those bolts that go from the uppipes to the manifolds, thats gonna be a pain. my trick is just tighten them, ive never had a set that didnt break from over tightening- Stroked
- Post #12
- Forum: 7.3 Aftermarket
-
S
Edge CTS mount 08 6.0 van...
the cts does come with a mount in the box, just a suction cup setup but it works fairly well. as for a pod, might have to contact edge support, theyre pretty helpful- Stroked
- Post #2
- Forum: 6.0 Aftermarket
-
S
F/S Garrett 38R with 1.15 Housing
How much for just turbo shipped to 21791- Stroked
- Post #2
- Forum: Aftermarket Performance
-
S
oil pan leaking "seal"
the back of the block could potentially be clean if theres a leak up above, theres a passage that it travels through, so it wont be on the back of the block it will be in that passage. thats why all your leaks make the puddle in the driveway the same spot. -
S
Wtb factory fender flares
As said, looking to buy the factory wheel over mouldings, or fender flares to if my 01, so 99-07- Stroked
- Thread
- Replies: 2
- Forum: Exterior Parts
-
S
Resetting keyless entry
nope, was ngs, then wds, then pds and ids, now pds is obsolete for the most part. wds is ancient, never worked efficiently anyways -
S
Drop in Batmowheel for stock turbos
any videos? maybe a dyno pull?- Stroked
- Post #56
- Forum: 6.0 Aftermarket
-
S
aftermarket oil temperature sensor
oil temperature gauge is in the mail, i see a lot of people buying 75 dollar oil filter caps, buuut being that its not a show truck, would drilling, tapping, and maybe even jb weld sealing the sensor into the factory oil filter cap work? or is there another reasonable place to put the sensor easily -
S
injector ?
the old 38r had a whistle, not sure what they changed, but any truck ive ridden in that had one now, sounds different than my 38r i bought a few years ago, went from a definite whistle to a whine- Stroked
- Post #15
- Forum: 7.3 Aftermarket
-
S
7.3 4r100 Flexplate
still available, bump...make me an offer- Stroked
- Post #2
- Forum: Engine and Drivetrain
-
S
Calling 6.0 gurus, wtf's with the lpop
the last one i think is my problem, that thick ass o ring that goes between the front cover and the o ring is holding me down, i might loosed them if i cant flex it enough with a lineup tool -
S
Calling 6.0 gurus, wtf's with the lpop
nope. its not like a 7.3, there isnt a different direction. ive been told theres some out there with circles on them, like timing marks, but the 3 sets i have here do not have anything of the sort. stupid, piss poor design.
