Search results

  1. B

    160 80s

    you have PM...:thumbup:
  2. B

    DP F5 - 11 tunes DAC3 6 spd

    i have a DP F5 for sale...going another route... the switch is the square one with green numbers. chip and switch are in great shape. a little mark on the face of the switch, cant tell if it could be cleaned off or not, just never bothered me. PCM - DAC3 1. stock 2. high idle 3. drive thru...
  3. B

    Wtb f5 or f6 dptuner

    i also have a f5...dac3 pcm code and 11 tunes. pm me if interested
  4. B

    F.F.D stage 1's for a 7.3

    pm sent:cool:
  5. B

    Vibration Damper install

    im sorry...you use a thinner washer...not sure of the size, but i just grabbed it from my stock. reread the post and the fingers were working faster than the brain
  6. B

    Vibration Damper install

    i just used the stock bolt without the washer, the once installed took out the bolt and installed the washer. i did use rtv on the key way. thats where it was when i pulled it, and i also read somewhere to use it...so far so good.
  7. B

    7.3 IPR Core

    payment sent...thanks man
  8. B

    Front and rear 2000 LE Leather Buckets and consols.

    i have a cloth set that are in great shape that id be willing to trade...2 small problems...im in PA and they are gray. they are in great shape, but have been looking for leather for a long time. let me know if interested...
  9. B

    What Causes a Push Rod to Bend?

    not the same cylinder. i dont think its the carrier...just the bolt. i haven't seen it, but in his explaination, he told me "both push rods on the pass side #2 cylinder were out of the rockers and the bolts were finger tight." then he realized that one of the "loose" bolts was actually broke...
  10. B

    What Causes a Push Rod to Bend?

    they are great guys...again, just wanted to do a little brainstorming and see what possibilities are out there to cause this...but after these responses...i think the assembly error is the only possible option thanks again everyone
  11. B

    What Causes a Push Rod to Bend?

    no thats the one...but we found out after fixing it sat day, nite and into sun am...he forgot to tighten a rocker bolt on the pass side, which on his way home caused the other bolt to shear off and and dislodge the push rod from the rocker. he pretty much drove 2 hrs on 7 cylinders...thats why...
  12. B

    What Causes a Push Rod to Bend?

    i dont think there was any possible way for fluids to be there...he used a vacuum pump to clean the cylinders and then with the gps out, he turned the motor over numerous times. it actually started after about 4 cycles of trying. he stopped for a while after the sound, but figured...the damage...
  13. B

    What Causes a Push Rod to Bend?

    maybe it was just installer error...just trying to cover all basis so i have a better understanding. i tried, when helping him fix it the second time, to miss the lifter, and it seems almost impossible...but i didnt install the initial ones. i know when i did mine with the 910 springs, i...
  14. B

    What Causes a Push Rod to Bend?

    no...just turned the key
  15. B

    What Causes a Push Rod to Bend?

    yes and yes...injectors were re o-ringed, and new cups were installed, all fluids were mitey vacced, the motor was hand cranked for about 10 revolutions. i assume, the valves seemed clear
  16. B

    What Causes a Push Rod to Bend?

    i wondered about the chain idea :shocked: anyway...the first second the key was turned the "cannon" sound started. very scary and loud, but in a perfect rhythm. no smoke, idle seemed fine, but hard to tell with the noise. he was trying to start it due to air from the work, and once the key...
  17. B

    What Causes a Push Rod to Bend?

    it wasnt new. same ones that were taken out. same rods, in same holes, with same rockers, on same cylinder
  18. B

    What Causes a Push Rod to Bend?

    this happened on the first key turn after re-installing them from an injector oring and cup r and r...what you said about high rpms and timing is what i have read. thats why im trying to figure this one out. he drove the truck right before repairs were made...thanks for all the thoughts
  19. B

    What Causes a Push Rod to Bend?

    we were thinking the same thing, but its awful hard to "miss" the lifter. just want to know for future reference...maybe it was:fustrate:
  20. B

    What Causes a Push Rod to Bend?

    here is the rod...again, it was the 2nd rod back on the drivers side [/IMG] what do you guys think?

Latest posts

Members online

Top