Recent content by XrayPipeliner
-
T4 mount questions
I have the kit with the s366 and it was only like 2200. Plus 800 for the waste gate. Way better than a 38r and bout the same price after bellowed up pipes and turbo- XrayPipeliner
- Post #22
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
So I should address my rods before my tranny? I just got my truck back today and drove it from West Virginia to michigan. Put it on the 120 tune and it jumps off the line good then I get a hesitation. And it slams into second gear.- XrayPipeliner
- Post #51
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
I'm not sure what way to go. Buy a used forged block and rebuild it. Pull my motor and put rods in it. I'm not a mechanic so I have to pay for all my labor.- XrayPipeliner
- Post #43
- Forum: 7.3 Aftermarket
-
99 forged rod long block 7.3l
Man I want it. But my money is funny right now. Wish I had something to trade!- XrayPipeliner
- Post #12
- Forum: Engine and Drivetrain
-
Gonna need rods, Stupid question...
Well FINALLY have everything and it's all installed. Few issues with the piece that connects the turbo to the down pipe. Jake sent another. Overnighted it even. Now I think I have a tuning issue. When the truck starts it acts like I have the lope idle tune until I rev her up. And at idle the...- XrayPipeliner
- Post #41
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
Still playing the waiting game..........- XrayPipeliner
- Post #38
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
I talked to Gary today they will be shipped tomorrow. The moved their shop to a different state, thats why the wait is so long.- XrayPipeliner
- Post #37
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
It was ordered from Jake at Irate. Do you have a number for Gary? My truck has been down this whole time and this job is ending so I will have to move my camper to the next job.- XrayPipeliner
- Post #35
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
STILL waiting on my SRP 1.1! Has anyone else ordered one of these and did it take 2 months to get it?- XrayPipeliner
- Post #33
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
If I ever get my tune! It has been 3 weeks at least. I havn't even drove my truck in a month. EPBV is stuck closed and I work 7 12's a week so do not have much time to drive it but it was warm today and I am ready to get out. All the parts in my sig are sitting here waiting on my hpop and tunes...- XrayPipeliner
- Post #32
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
Thats what I like to hear! I am still waiting on tunes. Ordered them the 12th, called monday and she said if I dont have them in a few days to email her. Did early today with no response. Hope the tune is worth the wait.- XrayPipeliner
- Post #30
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
I have a factory 2003 7.3. I heard they only made a few before switching to the 6.0- XrayPipeliner
- Post #25
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
It is an 03, I have not checked but Im sure they are. I wouldnt mind spending the money just means a slower build but I want it done right. I am also concernd about going too far to where I can no longer pull a 18k fifth wheel across the country if necesary. With good tuning I am guessing I...- XrayPipeliner
- Post #19
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
EVERYONE including my wife says the same thing, I am not budging! :stupid:- XrayPipeliner
- Post #11
- Forum: 7.3 Aftermarket
-
Gonna need rods, Stupid question...
Carrillo rods are really expensive!!:shrug:- XrayPipeliner
- Post #9
- Forum: 7.3 Aftermarket
