Search results

I’ve got a 2018 F-350 that my wipers only work on high. The squirter works and when you push it the wipers work on that speed aswell. I replaced the multifunction switch and same thing. Wiper motor ???

Looking for 8” radio bezel for a 17-19 F250. Manual AC controls

Trying to find out what the orientation of the 2 wire plug on my center console dual usb is. Not sure which one is 12v and which is ground and if that’s what h They actually are. Talking about the 4 pin side. There are only 2 wires in the plug. The outside 2 pins

I have a 2018 F-250 XL with the 4” radio but I have a 8” screen that I got from a friend. Looking for the dash bezel. What all do you have to do to swap ?

I have for sale a 2013 F-250 Platinum. Pearl white. 4WD 175k miles. Located in central indiana. $33k

Looking for a lower mile good 6.0 engine complete. Studded would be great aswell but I’m not gunna ask for to much.

I haven’t dealt a whole lot with the 6.7’s but I am currently having a couple issues with mine and going through the Ford service diagnostics for them it’s showing a PCM issue. But I’m having I real issue. I can’t believe it’s a PCM with only one sign showing up. Do the PCM’s on these trucks...

Can I remove the muffler on my stock 2013 and leave it all stock still. I just want it to sound like a truck but want to leave it all stick. Didn’t know if that would hurt the regen cycle. I realize I will have to leave the factory tip

I have a issue with my turn signals. When I turn one on the other blinks very dim. This happens when I have all other lights off. If I turn on my parking lights or headlights and my turn signals it doesn’t happen. I also have gotten a P208B code which is for the reductant pump stuck off. It is...

Any body have any idea what this means ? Do I need to replace this DEF pump or is there something else to do/ look for. Thanks

Got a 99 7.3 that I’m having starting issues with I have a snap on scanner I’m using and what I’m seeing is 450-510 icp pressure and 37% IPR at idle and when you take off the icp goes up around 800 psi and then the ipr is around 50-60% at wot I’m seeing 1100psi icp and it starts dropping but the...

Got a 6.7 for the farm.. all stock... curious if I’d hurt anything running red fuel through it ? I’m sure this has been discussed before but I couldn’t find anything on it. Thank you

2005 ford f-250 super duty fuel: diesel title status: clean transmission: automatic I have for sale a 2005 F-250 Crew Cab Short Bed Lariat. Truck has 220k miles. It has been fully bulletproofed. Never had a programmer. Runs flawlessly and has ZERO RUST. Leather heated seats. Drivers seat...

Having issues with my 05 randomly dieing. Most of the time it’s right after I have let out of the throttle at low speeds or when it’s sitting idle. It will start to act like it’s gunna die and then recover and run fine and then sometimes it dies.. every time it restarts just fine. I have...

I’ve got a 99 F-250 that I can’t get to start it has no voltage to the inertia switch for the fuel pump.. sits there and cranks but won’t fire.. also when I turn the key on there’s a few relays that chatter in the under dash fuse box. Also the dome light relay clicks on and off unless you pull...

I have a 2004 CCSB that I believe the fuel level sensor is taken a **** on. It gets below a half tank and will go up and down. It went back up to a half tank the other day and I ran out. I think I’m gunna have to pull the tank and replace. My question is has anyone ever put a 38 gallon tank in a...

I’ve got a 05 CCSB that I just put 33’s on and now I have alittle sway in the steering. I think I may have had it before alittle but now I really notice it I’m. It a suspension guy. Is there any steering component imperticular to look at for this issue ? I’m thinking of putting a dual steering...

Has anyone replaced the gaskets on a oil pan with the motor still in the truck ? Just curious on how difficult it is and a estimated repair time.

I’ve got a 2005 CCSB F-250 need to replace the carrier bearing or center support bearing whatever you want to call it. Would like to do it quickly and have the parts on hand before tearing into it. Does anyone know the shaft size ? There are a few options and they appear to be fairly close

On my 05 when I key on the fuel pressure builds quickly to around 65psi truck starts and runs good fuel pressure stays good.. when I shut the truck off the pressure drops to 0psi pretty fast isn’t there something that keeps it from dropping that low ? Like a check or something I don’t ever...