1995 F-350 Overhaul

Beau · Mar 21, 2013

Started on this project a while back, starting to make some progress finally motor is getting machined right now.

Beau · Mar 22, 2013

Few more pics of what is happening on the project. Currently setting up the engine with carrilo rods, mahle pistons coated -1.5 pts Compression ratio. Getting Balanced linehoned with girdle and ARPs,- heads ported fire ringed with ARPs, bowled shimed comp 910's. ,SRP 1.1, 300/200 injectors, Turbo setup S467 /S483 with dual 60mm turbosmart wastegates, and a small refrigirator / air to water intercooler. Phoniex Single Ceramic Clutch.

Hoping to make a few ponies, and still be decent to pull the bobcat around.

Any tips im open.

Beau · Mar 22, 2013

some pics here

Buffalo444 · Mar 22, 2013

badass

Beau · Jun 13, 2013

So things have changes a bit and they always do. I was originally gong to run a twin but now it's going to be a thriple setup 66/82/106. Any hi I would like to run beehives from comp need some set pressure for the boost. Anyone running them. Wondering about insta procedure.

Thanks

Beau

POWER-STRUCK · Jun 13, 2013

sounds like a cool build! the single ceramic might make it hard to pull and back a trailer, i've made that mistake a dual disc worked much better

Beau · Jun 14, 2013

Very true, I figured it was going to be all or nothing pain in the but. I bought the clutch from a very small tranny shop here in St. Cloud. Nice old guy, so I bought whatever he had and this is what I ended up with. Thanks for the advisement can always swap it out.

Beau · Jun 14, 2013

Some changes in build plan besides an additional turbo include. Injectors 400/200 from farmers via vision diesel. Regular air to air intercooler, got the whole turbo kit from Vision for to good of a deal and inter cooler from ponticross. Hpop setup will be my stock 15 and a gen 3 from another member on here. Waste gates changed to 46/39/39 all percision units. Anyhow hoping on getting my engine back by Friday.

Krause · Jun 14, 2013

Looks good, what did you coat your frame with?

Beau · Jun 15, 2013

Por 15 rust paint and then por15 semi gloss top coat

Beau · Jul 24, 2013

and so it begins

bad12jr · Jul 24, 2013

I'd seriously look into a clutch. That clutch will die almost instantly with that many ponies. And the ceramic is either on or off. Not much slip if any. My ceramic /kevlar is not fun to back up and its no where near as grabby.

Sent from my DROID RAZR HD using Tapatalk 2

Beau · Jul 24, 2013

http://powerstrokearmy.com/photopost/data/500/medium/photo62.JPG
http://powerstrokearmy.com/photopost/data/500/medium/photo_4_3.JPG

Lots of parts and still no motor yet

Beau · Aug 5, 2013

All most done fabing up my fuel cell, 45 gallons, with a sump in the bottom.
http://powerstrokearmy.com/photopost/data/500/medium/Fuel_Cell.jpg
http://powerstrokearmy.com/photopost/data/500/medium/fuel_cell_2.jpg

earlybroncoboy · Aug 9, 2013

that is a nice looking work bench you got there!!!!!!!!!!!

Beau · Aug 12, 2013

Thanks, lol. Just got the motor back from my machinist, going to start assembling this week, once I get the motor assembled, Then the piping nightmare begins trying to get everything to fit.