Question for amp step owners

zporta · Nov 27, 2015

I am about to pull the trigger on a set of amp step, but have a few questions first.

Those have installed them, do you have any pictures of them in the closed position under the truck? I have my air compressor and tank under my truck and want to confirm that there won't be any contact with what is mounted.

Thanks guys

Dzchey21 · Nov 27, 2015

it might be better to post a picture of your compressor to see exactly what you need from us. they tuck pretty tight there isn't much room for anything.

Tom@BigTimeKustomz · Nov 27, 2015

Mine suck up right behind the pinch weld under the doors, if that helps you.

zporta · Nov 27, 2015

I have these two pictures, but it's hard to tell from the photos where the stuff is in relation to the pinch weld.

http://i265.photobucket.com/albums/...3-642C-45F8-A571-EE551BB78E1E_zpsohwephku.jpg

http://i265.photobucket.com/albums/...A-E9B6-4FBD-B5D2-0ED4AE229FEF_zpsyqle64gf.jpg

When I get back from visiting family I can get a better picture. If anyone could snap a shot of their steps install that would help greatly

Jmuck · Nov 27, 2015

You're most likely going to have move the compressor and tank. Looks to be right in the way of the steps resting position.

zporta · Nov 27, 2015

Jmuck said:
You're most likely going to have move the compressor and tank. Looks to be right in the way of the steps resting position.

That's what I'm worried about. I have been looking everywhere for pictures of the resting on the internet

not enoughsmoke · Nov 28, 2015

this pic is them on my 95 Fummins i don't have pic of them on my 99 Fummins

jcain · Nov 28, 2015

jcain · Nov 28, 2015

zporta · Nov 28, 2015

Thanks man, looks like I'll have to move the tank. The compressor might be fine where it is. I guess I won't know till I have them in my hands

mwdguy · Nov 29, 2015

My bestop boards

[/URL][/IMG]

manual6.0 · Dec 2, 2015

mwdguy said:
My bestop boards

[/URL][/IMG]

curious, what do you have protecting the bottom of your doors that is bolted to the pinch weld?

zporta · Dec 2, 2015

Look what showed up today

I held one bracket up just to see where it sets and I might clear. Hopefully I can get it installed this weekend

Clean-15 · Dec 3, 2015

manual6.0 said:
curious, what do you have protecting the bottom of your doors that is bolted to the pinch weld?

http://www.rockerflares.com/rockerflares/#ford

zporta · Dec 4, 2015

I swapped my factory steps onto my Dads 2015 XL f250. And after almost busting my ass every time I stepped out of the truck I knew it was time to jump on the install. I was going to wait for the weekend, but didn't want to wait and tear up my seat or a knee reaching for a step that wasn't there.

Very simple install other then the door trigger wires. When it comes to wiring, that is my one mechanical downfall. Especially fining 4 wires in a loom of 50. The quality of this kit is top notch and everything went together flawlessly. And much to my pleasure it cleared all my air components by an inch. I only had to move my air Chuck which I had coming through a hole in my pinch weld.

I'll post some pictures later, it was getting pretty dark when I finished.

Here is the step swap from my truck to my dads

ckrueg · Dec 4, 2015

Clean-15 said:
http://www.rockerflares.com/rockerflares/#ford

How do those work. I looked at them but It looked like I would have to drill holes in the body so I never got them.

Sent from my SM-G900V using Tapatalk