No oil coming from injector spout

jpow95 · Apr 16, 2018

Icp 1500
Fuel pressure at 58psi
New cam sensor
Fuel pulse .60
If I hold up a gas rag to the intake it will fire off to start but will not run under its own power getting black smoke from exhaust anyone ever run into this

Sent from my iPhone using Tapatalk

dsberman94 · Apr 16, 2018

Don’t start new threads on the same problem. Makes it hard to figure out what’s wrong when we have to go back to other threads to find that info.

Bad pcm or idm.

jpow95 · Apr 21, 2018

Changed idm with known working one still issues did get it started but will only drive about 1 Mile before shutting down and getting a no start again did install new 160cc injectors from black cloud and ran great for about a mile now getting p1272 -p1278 codes going to ohm the injectors then to the idm I did install new wire loom on the engines side and I didn’t see anything strange so gonna test and let y’all know

Sent from my iPhone using Tapatalk

jpow95 · Apr 21, 2018

I do apologize for double posting I didn’t see it post the first one

Sent from my iPhone using Tapatalk

jpow95 · Apr 23, 2018

Getting black smoke like little puffs smoke and sounds like it’s firing only on a few cylinders I drove it to 45miles no problems next day it drove 2 miles before stalling then added the new injectors and hydra chip for the injectors then drove 2 miles before stalling now I’m just getting black puffs of smoke but won’t fully start just crank icp above 1000 while cranking new cam sensor dorman valve cover gaskets

Sent from my iPhone using Tapatalk

sootie · Apr 23, 2018

if the under valve cover harnesses are Dorman, I have heard that they are bad news.

jpow95 · Apr 23, 2018

I did replace with ford oem and still same issue sounds better while trying to crank but still no start unless a gasrag is held up

Sent from my iPhone using Tapatalk

jpow95 · Apr 23, 2018

I also would like to mention I do not have a wait to start light but can communicate with pcm and also I swapped pcms with a new one still same problem and still no wait to start light

Sent from my iPhone using Tapatalk

psduser1 · Apr 23, 2018

If it's only firing on a few cylinders, than I'd say pull the injectors and check the orings, and possibly swap in a different set of injectors altogether, If you can.

jpow95 · Apr 23, 2018

I had the original 250k in and it ran great then had it stall out then installed new injectors and still a crank no start possibly a air lock in the fuel system

Sent from my iPhone using Tapatalk

lincolnlocker · Apr 23, 2018

Who the f is black cloud? Lol.. what is icp duty cyle while cranking?

live life full throttle

jpow95 · Apr 23, 2018

Swamps was 3 weeks out to build the injectors so we went this route icp is up at 2200

Sent from my iPhone using Tapatalk

jpow95 · Apr 23, 2018

Ipr is up at 40

Sent from my iPhone using Tapatalk

PsdPullerJr · Apr 24, 2018

Your not seeing a wait to start light? Is the fuel pump coming on?

lincolnlocker · Apr 24, 2018

jpow95 said:
Swamps was 3 weeks out to build the injectors so we went this route icp is up at 2200

Sent from my iPhone using Tapatalk

Oooohhh, you got Nate's injectors from black cloud. Thats good. Just didnt know who black cloud was. Ipr dc is a bit high but it should still fire at that icp. If no wts light then it might have a bad reading from pcm. How are the batteries and alternator doing? What is cranking voltage?

live life full throttle

psduser1 · Apr 24, 2018

Sounds like you have hpo, now, anyway.
As mentioned, verify fuel pressure.
If that is 50 psi or higher, than you are back to an electrical issue.
All the connectors are tight, I assume?