Recent content by a_moore
-
DTA360 Re-Power
Installing a 6.0 vgt charger. Not happy with the S360 response. Mocking up with a stock turbo, then install the KC stage 1. Only programming away for the vgt.- a_moore
- Post #140
- Forum: Engine Conversion
-
DTA360 Re-Power
If you gently floor it 15psi no smoke. If you mat it 35psi and lots of power. I kind of like it as is. Not freed up all the way. I'm not convinced my pedal and spring are correct. I used too strong of a return to idle spring on side of pump. Pedal is stiff. I'm pulling that junk ass slick Jegs...- a_moore
- Post #138
- Forum: Engine Conversion
-
DTA360 Re-Power
Whatever was in there from bus. It runs the same temp in February. Warms up good and quick.- a_moore
- Post #135
- Forum: Engine Conversion
-
DTA360 Re-Power
It's been hot and I still don't break 180f. 174 is about average. Rev it up half way all the time sitting to use compressor. My 1hp snap-on grinders are nice, but they use air like crazy. It keeps up pretty good at 1800rpm or so. Hauled big loads of cattle and hay in the heat. Don't think I'm...- a_moore
- Post #133
- Forum: Engine Conversion
-
'21 custom front bumper
Lights in. Going to make matching for rear.- a_moore
- Post #10
- Forum: Welding & Fabrication Forum
-
'21 custom front bumper
Done till I decide if I want grill guard on top.- a_moore
- Post #9
- Forum: Welding & Fabrication Forum
-
'21 custom front bumper
The dimensions are 60" wide, 32" front to back and 32" high. Firebox is 32" deep, 32" tall and 20" wide.- a_moore
- Post #7
- Forum: Welding & Fabrication Forum
-
'21 custom front bumper
What you wanna know? It work ls very well. I designed a drawer type fire box (maybe should have patended) that is easy to load and doesn't waste heat adding etc. You baffle the incoming air by how far the drawer is open. Then a cook rack for smoking and a higher one for steaks, pizza, sides that...- a_moore
- Post #6
- Forum: Welding & Fabrication Forum
-
-
'21 custom front bumper
Looks like it stick out far in photos. Doesn't really.- a_moore
- Post #2
- Forum: Welding & Fabrication Forum
-
'21 custom front bumper
Almost done with the new bumper. Got backed into and didn't want to replace with more junk. What do you think of this? 2"x6"x1/4" wall tube. Got to mount cruise sensor and fog lights. About time to paint.- a_moore
- Thread
- Replies: 9
- Forum: Welding & Fabrication Forum
-
DTA360 Re-Power
175°f is all the hotter it gets. What have others done for cooling? I had planned to add electric fans but i do not find a kit for the 6.4. Might have to buy a 6.0 kit and make it fit. I can only assume getting stuck in traffic towing on 100° day may be an issue. As it keeps warming up, im...- a_moore
- Post #132
- Forum: Engine Conversion
-
-
DTA360 Re-Power
Ether makes it start right up with no issues. I am gonna put an ether injector on so i just push a button. Dont want to open hood in cold and snow. Maybe when i get the compounds done i can have access through grill to intake. The injector would be better long term.- a_moore
- Post #129
- Forum: Engine Conversion
-
DTA360 Re-Power
Did you see this one I did a couple years ago? It's my holding tank now for compressor on engine. Nice for hay season blowing out radiators etc.- a_moore
- Post #120
- Forum: Engine Conversion
