Search results

  1. G

    6.0 Fuel pressure question causing no start?

    The mounting surface was clean where the cam sensor mounts and the rpm signal is constant. The cam sync signal to FICM is constant but the crank to cam sync signal cycles at a constant interval.
  2. G

    6.0 Fuel pressure question causing no start?

    The EGR has been deleted.
  3. G

    6.0 Fuel pressure question causing no start?

    The new crank sensor and ICP sensor (OEM) were installed and still no start. The ICP pressure builds in approximately 10 seconds to 1500-2000 psi. The truck is gray smoking as it is cranked and has a slight smell of fuel. The crank to cam sync still drops from 1 to 0 in a timed/cyclical basis...
  4. G

    6.0 Fuel pressure question causing no start?

    It took a while to remove the crank sensor but it looked good and the tone ring didn't move when I pushed on it with a screwdriver. I don't have anyone to work with me to spin the motor while watching the tone ring so that test is out for now. Ordered a new OEM crank sensor and waiting for it to...
  5. G

    6.0 Fuel pressure question causing no start?

    I'll check ICP voltage later today if possible. Forgot to mention earlier that the truck is not throwing any codes when trying to start. The crank sync is "pulsing" on and off but not throwing a code. Currently trying to remove the crank sensor and it is fighting the whole way! Thanks for the...
  6. G

    6.0 Fuel pressure question causing no start?

    Attempted to start the truck again after installing a 6.4 starter, 6.0 starter failed. The engine RPM was at 288, ICP peaked at 2255 psi then dropped to 1545psi, ICPR started at 14% then jumped to 85% then dropped to 48% once pressure developed. The FICM sync was steady but the crank and cam...
  7. G

    6.0 Fuel pressure question causing no start?

    The oil pressure mentioned is high pressure and it is approximately 2000psi.
  8. G

    6.0 Fuel pressure question causing no start?

    Still working with a no-start issue. The fuel pressure builds to approximately 45psi when the key is cycled but quickly drops back to zero if the truck isn't started. I am thinking this has something to do with my truck not starting so I am questioning if this quick drop in pressure is normal. I...
  9. G

    WTB: 7.3 Billet Rods

    PM me with price(s) of the new sets.
  10. G

    WTB: 7.3 Billet Rods

    Looking for a set of billet rods (Crower, Manley, Carrillo) for a 7.3 power stroke. Wanted to check here before ordering a new set.
  11. G

    6.0 Starting Issue

    The resistance between pins 31 and 43 is 810 ohms. I will have to get some angled, small meter leads to check the frequency across the pins. Thanks for your help
  12. G

    '02 F250 Dataport connection wiring diagram

    Does anyone have a wiring diagram/pinout for a '02 F250 7.3 dataport connector (ODB II plug)? Have an older tuner (Infinity) that is able to connect and pull error/trouble codes but not able to upload my tunes to the truck. Thank you.
  13. G

    6.0 Starting Issue

    The sensor mounting surface was relatively clean. I wiped it down good and made sure to seat the sensor when installing it.
  14. G

    WTB: 6.0 FICM Logic board

    Several "spammers" have contacted me the same day they joined.
  15. G

    6.0 Starting Issue

    The RPM fluctuates some and the cam sensor has been replaced with a new oem sensor. I am willing to troubleshoot the sensor if that could be the issue of the cam/crk sync coming and going.
  16. G

    6.0 Starting Issue

    I checked the truck again today with the AE software and noticed the cam and crank sensor sync is coming and going. I also had an "injector 1 low circuit" error come in while cranking. The high pressure oil is slow to build and the truck seemed to be turning slower than normal (180-250rpm) even...
  17. G

    6.0 Starting Issue

    I have tried two different FICMs with the same results. Plugged and unplugged the FICM connections with the same results.
  18. G

    6.0 Starting Issue

    Finally checked the fuel pressure and it is 55-60 psi once the pump energizes. The pressure falls to 0 once the pump is off and the fuel bowl is empty when opened. Is this normal? The truck had started a few weeks ago but now just stumbles like it is trying to start but doesn't. Any help would...
  19. G

    6.0 Starting Issue

    A new injector harness has been installed and a new plug on the main harness so all three seat firmly in the FICM. The truck now "sputters" when it gets past 550-600 psi ICP. The FICM sync looks good as does FICM voltage. The batteries were tested but drop to under 11v when starting as seen in...
  20. G

    WTB: 6.0 FICM Logic board

    Looking for a good logic board half of a 4 pin FICM for a '07 6.0. Thanks.

Random media

MBRP DP
no_limit_shirt1
trips_completed
Chilling
292490_4050142579556_1897481452_n
1511MG-160
2011-04-12_18-12-02_649
374026_3590699413764_681334396_n
dieselx2
2012-09-07_20-40-07_144
IMG_43941
DSC02027

Latest posts

Members online

Total: 311 (members: 2, guests: 309)
Top