Search results

  1. morefuel

    6.4 high idle help

    Yep, programming calls for a higher idle rpm for cooler coolant temps and an additive for ambient air temps.
  2. morefuel

    Cracked Head @ Fuel Fitting...Now What??

    Any way you could retap it further in and put a boss fitting with tape? Not sure how or if that would work.
  3. morefuel

    Looking for a 24” light bar

    I got a bar from Tractor Supply for Christmas a couple years ago and it is still sealed and works fine. The lens seems to be yellowing just a little though.
  4. morefuel

    Engine load

    Check engine and trans temp sensors. Seems like it show up somewhere obvious but sounds to me almost like it is thinking things might be cold.
  5. morefuel

    Midwest 6.7 compound kit

    Mind saying what smog laws changed?
  6. morefuel

    Donaldson Blue 6637 air filter, better flow and filtration

    Modded box makes a huge difference. I think i could suck my minder in a half throttle. Pulled the lid off and left the filter in my version of modded box and it doesn't move. Not sure how old the filter is either.
  7. morefuel

    Calipers getting loose

    I should clarify. It was the bolts that supposedly need replacing.
  8. morefuel

    Calipers getting loose

    I heard once that if you pulled them they needed to be replaced. I've always used locktite and they've been fine though.
  9. morefuel

    Driveline vibrations

    I had a one that the yoke had to be bolted to the flange in one certain position otherwise it would vibrate. But that was flange mount yokes on each end instead of a slip. Not sure if you could try putting it on the splines in different positions or not. Or that flange on the axle side.
  10. morefuel

    Secondary cooling system puking from overflow hose

    I thought I had read somewhere before that the no limit CAC would accept more heat than the radiator for it could disipate. Not sure if that's worded correctly.
  11. morefuel

    My no frills (only necessity) build

    Just rock chip protection.
  12. morefuel

    Aftermarket cam Emissions compliant

    So far they don't test for nox. Hopefully they don't start.
  13. morefuel

    Aftermarket cam Emissions compliant

    So nobody has any ideas on how it will affect E gr flow or the D p f ability to burn off? I'm also interested in what peoples experience has been with aftermarket Cams and just tuning.
  14. morefuel

    Aftermarket cam Emissions compliant

    I have a 2008 6.4 that I'm thinking may need new valvetrain soon. And beings I live in CA I need to pass emissions testing from time to time. I've been looking at the straub cam beings it appears to get somewhat better fuel mileage, but would consider others. The question is, how will they...
  15. morefuel

    6.7 and FTE resonator??

    Did you get the donaldson muffler in backwards? They, or at least the 5", have a funny whistle if its in backwards.
  16. morefuel

    OBS 05+ axle swap

    I agree that you don't really need hydroboost to do the conversion. Do need the f-superduty proportion valve ****** or gut your old one though. My opinion on it is that even on the newer pickup not all of them have hydroboost.
  17. morefuel

    Washing/Detailing

    I've heard just spritz the pad with a little water or detailing spray.
  18. morefuel

    5.4 SPRINGS ON 2WD 6.0

    The Problem I would see, is correcting the camber. I believe that's why it's not talked about.
  19. morefuel

    Upcoming Head Gasket replacement

    Total different motor but when I took my Honda head to get checked all the intake valves were bent some. but only one cylinder was bad enough to notice any compression loss. They told me that the valve will flex just a bit and still seal but eventually the flexing can cause it to break.
  20. morefuel

    Is my block cracked?

    I have a motor from a person that was having problems with mixing also. He just drained the coolant and ran oil.

Latest posts

Members online

No members online now.
Top