Search results
-
Somewhat new to 6.7
Ok, not new to Powerstroke, just this one. 2012, all the junk off, exhaust on and Patriot mapping. Is there anything else that's really necessary or any revised update kits for this one? I'm talking like the little things that were overlooked like the blue spring kit on the 6.0s, body mount...- Nic
- Thread
- Replies: 4
- Forum: 6.7 Aftermarket
-
Fuel Filter 'kit', is it worth it?
Or just do what I'm going to do and install my Fuelab setup I have sitting here and swap out the upper factory to HS that flows more fuel and be done.- Nic
- Post #36
- Forum: 6.7 Aftermarket
-
H and s firmware update?
Can someone pm me on information to where I could get updates for a minimaxx? Thanks!- Nic
- Thread
- Replies: 2
- Forum: 6.7 Tuning
-
POWER SEAT ISSUE!
Got it fixed. The box was the memory control module which hasn't worked in a while and slowly killed a circuit on the board. I bypassed the memory module. Cutting and splicing but glad to have my power seat back up! -
POWER SEAT ISSUE!
Ok, not sure if anyone else has dug this deep, but my driver side seat quit working. I have removed both driver and passenger seat from the motor and track assemblies. I tested the motor and track from the driver side to the passenger side and it works. I'm getting power to the driver side, but... -
New tunes?
It's literally been a couple years since I've been on here. I'm getting my 6.4 flex plate replaced and doing a convertor while I'm in there. I want to get a new tow tune written for it. I have GH now and have always been pleased with their tuning. My question is, is there anything that's the...- Nic
- Thread
- Replies: 3
- Forum: 6.4 Aftermarket
-
Hotter oil temp after bypass oil install?
It's happened twice now. Two different 6.4s. No oil temp issues before and now they act like they have oil cooler issues. Haven't had a problem on the 6.0s. I would figure adding a quart to the system and running it outside wouldn't make it run hotter. Run cooler or stay the same. Anyone else...- Nic
- Thread
- Replies: 14
- Forum: 6.4 Aftermarket
-
-
SOMEONE has to have an answer..
Is that what its called? I tried "power window and lock harness" on eBay but no luck. Thanks for the tip.- Nic
- Post #3
- Forum: Aftermarket Electronics
-
SOMEONE has to have an answer..
My wife has a reg cab xl...no power door locks, windows, nothing. I'm converting it to a lariat. Already have power lariat chairs wired up, now I need advise on how to, or what to wire to make the power windows, door locks and mirrors to work. I would assume all factory switches just need a...- Nic
- Thread
- Replies: 8
- Forum: Aftermarket Electronics
-
high icp and irregular ipr iissue
Could be. Or not plugged in all the way. I'm going to check it as soon as it cools down. The blue pigtail was the one it came with, with the new icp. -
high icp and irregular ipr iissue
Just changed the ICP and IPR in my wife's truck. 03. My idle warm is around 880psi and ipr at 30-31%. It was a motorcraft icp. Could it be bad or my pigtail not correct? The pigtail it came with had blue wires. Still has a sparatic idle every once in a while but the values are too high. Icp... -
crank case venting idea
This was an easier idea than a catch can was my point and I wouldn't have to spend 800 dollars on some fancy catch can that someone built. I just mainly want to cut down on the vapor that plumes up from under the truck. I would run it to the exhaust but then it would look like the truck is...- Nic
- Post #3
- Forum: 6.4 Aftermarket
-
crank case venting idea
A little tired of seeing the trashy look of the smoke coming out from under the bed. What about running the hose from the crank case, down the frame about 3-5ft or so and putting a 'Y' fitting and going back up to the intake with a slightly smaller diameter hose. Maybe this would suck most of...- Nic
- Thread
- Replies: 45
- Forum: 6.4 Aftermarket
-
-
6.4 Coolant Tank w/ Battery Tray
Awesome! Sure would look good powdercoated to match under my hood ..- Nic
- Post #8
- Forum: No Limit Fabrication
-
-
DPC BS thread
Not so good. He lost boost mid way through the pull for some reason. When he got back in it it sounded like it was only at 70% throttle and didn't go very far after that. Great job to the Ford team this year! I think we did awesome. Awesome enough to burn down the duramaxes too LOL. Congrats to... -
-
DPC BS thread
That's the truth. Sadly. Fukkers.. Should have let them battle it out right.
Latest posts
-
Will a 1996 F6TZ-9A451-F engine wiring harness work on a 1997 f250 HD ?
- Latest: 6.7powersmoke
-
-
-
-
Members online
No members online now.