Search results
-
D
06 no start condition
Also pulled the oil filter and cap. The reservoir was empty, but filled up immediately while cranking. -
D
06 no start condition
No air test yet. It’s my next plan. I was kind of thinking maybe the stc fitting or an oil leak. It’s always ran solid. It gave no signs of the pump going out. I drove 150 miles then shut it off. I didn’t move till the end of the day and it wouldn’t start at first. It finally made enough... -
D
06 no start condition
After 316,000 miles, I think my truck finally needs the hpop. With the scan gauge, it would only read 250-400 icp. I unplugged the icp sensor and it shoots to 1573, and still does not start. Other than the hpop, what else could it be? -
D
Best headlights
In my 09, I used morimoto mini h1 projectors and a 55watt 5k hid kit. Worked awesome. I found some retrofit ready unsealed headlights that made the process very easy.- Diesel625
- Post #7
- Forum: 6.4 Aftermarket
-
D
6.0 bullet proof fan upgrade
I was wondering about the harness not being plugged in any longer. I know it throws a soft code, just wondering about the electronic side.- Diesel625
- Post #4
- Forum: 6.0 Aftermarket
-
D
6.0 bullet proof fan upgrade
I finally went ahead and upgraded to the manual fan clutch. My electrical clutch would work when it wanted so I figured I’d try it out. It works great. The AC is even colder than it has ever been. Has anyone ever had any issues with this setup?- Diesel625
- Thread
- Replies: 17
- Forum: 6.0 Aftermarket
-
D
2006 oil sending unit threads
Got it in today. Works awesome. This fitting saves a lot of time and labor. I’d definitely recommend it to anyone. -
D
2006 oil sending unit threads
https://www.accuratediesel.com/6-0l-/-6-4l-powerstroke-oil-pressure-/-temperature-thread-repair-adapter.html Try this -
D
2006 oil sending unit threads
Correct me if I’m wrong but couldn’t I just plug that port and thread the sensor into the oil filter cap? -
D
2006 oil sending unit threads
I found a oil pressure sensor thread repair fitting made specifically for the 6.0 and 6.4. It says it has 1/4” longer threads for this reason. Anyone familiar with it? -
D
2006 oil sending unit threads
Got the low oil pressure warning on the dash today. I went and bought a new sensor, and when pulling out the old one, the threads came out on the sensor leaving no way of installing the new one. I’m pretty sure I’m going to have to remove the cooler to change the cover, or is there any other way... -
D
Stock exhaust
I was wondering how bad the factory downpipe restricts the exhaust. For tuning all I run is a 40hp FICM tune. The cat and muffler are ******d as well. I’d like to run a 4” exhaust, but if I’m not going to benefit, I’d rather spend money elsewhere. My thoughts were to run a 3.5” downpipe and a...- Diesel625
- Thread
- Replies: 6
- Forum: 6.0 Aftermarket
-
D
Stock boost numbers
I kknow the boostgauge will not work without the map sensor plugged in. The gauge wouldn’t work after plugging the map sensor back in. The icp at full throttle is around 3300-3500 psi. -
D
Stock boost numbers
I put a new hose on the map sensor since the old one was dry rotted and did not fit snug on the intake side. I also put a new map sensor since after unplugging the old one, my boost gauge stopped working. It actually gained a few pounds of boost, and does not feel as sluggish as before. It hits... -
D
Stock boost numbers
Cleaned it 6 months ago when I did the egr ****** and oil cooler. It wasn’t even bad then. -
D
Stock boost numbers
Also, every now and then it idles rough. It always smooths out once I throttle it. I’m going to try and check the map sensor when I get off work today. -
D
Stock boost numbers
It doesn’t have any leaks. I even put new up pipes because one of the bellows cracked. -
D
Stock boost numbers
For a while now, my 06 has seemed low on power. If at a stand still, you can floor it and it takes off really slow. It picks up power eventually. My boost gauge will not go over 20-21, no matter the situation. Up hills it’s a slug. I have a scangauge, and how could I use it to trouble shoot. No... -
D
********** diesel Mansfield, tx
********** diesel. Not the real guys from Elkton,MD.
