Search results
-
TC tail shaft installation
Looks like the factory uses some type of gray our TV but it's not TA – 31 I don't think, it came off fairly easily Just curious, that's all I will probably use this Pirma Tex ultra gray. I have sitting here. Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #3
- Forum: 94-97 Tech
-
TC tail shaft installation
Which RTV do you guys prefer when putting the tail shaft back on the transfer case? Sent from my iPhone using Tapatalk Pro- JohnT24
- Thread
- Replies: 4
- Forum: 94-97 Tech
-
-
obs drive shaft length
Yes Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #2
- Forum: Suspension, Drive Train, and Tires
-
-
97 wont start
Did you check the air in the tires? Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #14
- Forum: 94-97 Tech
-
Transfer case slip yoke slop
Camerota truck parts got me a new bushing (bought 2) Hopefully be in tomorrow Nice to have a press . Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #9
- Forum: 94-97 Tech
-
Transfer case slip yoke slop
I went to Napa after work / that was a waste Called the Ford dealer and they gave me the bushing part number but it's obsolete FOTZ7085B I called Camerotas and seems like they can help, but I need to identify which transfer case I have. Its a BW I'm pretty sure it's a 1356 Anyway, I'm...- JohnT24
- Post #7
- Forum: 94-97 Tech
-
Transfer case slip yoke slop
Yeah, I just found out about that bushing. I am going to take the tail housing off today and take a look I'm thinking maybe that little slop I have is actually the bushing and not the yoke Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #5
- Forum: 94-97 Tech
-
Transfer case slip yoke slop
Anyone know where I can get one? (I will check Napa on Monday) Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #3
- Forum: 94-97 Tech
-
Transfer case slip yoke slop
I'm pretty sure I have a Worn slip yoke Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #2
- Forum: 94-97 Tech
-
Transfer case slip yoke slop
95 F350 / 133" WB When I put my 4 inch lift kit on the truck, the rear driveshaft slip joint, where it goes into the transfer case was approximately 1/2" out from where it was originally. I did not think that 1/2" out would hurt anything since it was still on the output shaft about 2 1/4...- JohnT24
- Thread
- Replies: 8
- Forum: 94-97 Tech
-
OBS front fuel tank sending unit
Thanks tapatalk [emoji849] Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #5
- Forum: Want to Buy
-
OBS front fuel tank sending unit
Location 267 Neal Rd. North Pitcher, NY 13124 Contact Us Phone: (607) 486-4001 Email: [email protected]- JohnT24
- Post #3
- Forum: Want to Buy
-
OBS front fuel tank sending unit
10 years ago I had both sending units rebuilt from Tri-starr in NY Cant remember exactly but I know it was a LOT cheaper than new ones. They did a great job and soldered in 3/8 tube so I can run rubber line instead of the stock clip on configuration. Highly recommend them. Sent from my...- JohnT24
- Post #2
- Forum: Want to Buy
-
Turbo pedestal oil leak after replacing O rings
Yeah, I don't know if I would resort to JB Weld. You would be better off to pull the whole engine out and TIG weld everything together [emoji1787][emoji1787][emoji1787] BTW, I used the (thin layer) RTV on the top and bottom O-rings..... Also, I'm not sure if it matters much but I put mine...- JohnT24
- Post #70
- Forum: 94-97 Tech
-
Aftermarket headlights? That actually look good..
That's a little too Ghey for me. [emoji304] Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #15
- Forum: 7.3 Aftermarket
-
Turbo pedestal oil leak after replacing O rings
I just remembered I bought my O-rings from the local international dealer. They were noticeably more pliable and thicker than the cheap O-rings that came with the KC turbo. Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #68
- Forum: 94-97 Tech
-
Turbo pedestal oil leak after replacing O rings
Who's O-rings are you using? I just recently installed mine and I was so paranoid that it would not seal right that I insisted on official FORD o-rings I did not want to use the brown O-rings that came with the kc turbo So, along with those Ford O-rings I also put a light coating of...- JohnT24
- Post #67
- Forum: 94-97 Tech
-
Anyone recognize this plug?
Directly under the assesory power plug/cig lighter. (Not the one in the ashtray) Sent from my iPhone using Tapatalk Pro- JohnT24
- Post #8
- Forum: 94-97 Tech
