Anyone interested in a DYI Billet 66mm OBS-E99 Kit

NRHX2009 · Apr 10, 2013

Yeah, there is one in Pine Grove. Stumps Garage. Its like 75 bucks for 3 runs. I'll cover the costs. Only little problem is no results with a stock turbo vs 66mm.

The only bad thing is the dyno is normally booked on the weekend.

OldschoolPSD · Apr 10, 2013

I think we could swap the cover and wheel on the truck if you have a spare stock set. That way we could get back to back runs.

OldschoolPSD · Apr 10, 2013

There is a chance I could get up there Friday morning. I'm free all next week but I don't think that does you much good

NRHX2009 · Apr 10, 2013

It might... I have a stock wheel and housing but the turbo needs pulled to do the swap :/ time consuming on an obs.

I'll get results with my e99 eventually. But just to do a run would be great with your truck.

I'll let you know what day next week he can get you in. Any day? for me it has to be 3:45-4:00 dyno time.

OldschoolPSD · Apr 10, 2013

That works. Let me know

c69ss396 · Apr 19, 2013

I might be interested in giving this a try in my truck, It could give you some real work truck results.

OldschoolPSD · Apr 20, 2013

38.2 psi before it defuels. I'm gonna build a boost fooler tommorow.

I've been chasing a short in the engine harness but I got it figured out now. Should have some real numbers for you guys soon.

NRHX2009 · Apr 20, 2013

good deal. Let me know if you want to re schedule dyno for another day.

OldschoolPSD · Apr 21, 2013

I'll PM you about it.

gnxtc2 · Apr 24, 2013

I have a D66 and Baby Hybrids (hybrids with stock nozzles). Which billet wheel replaces the D66 one?

Billy T.
[email protected]

OldschoolPSD · Apr 24, 2013

Put it to work today grossing 20k. No surge or anything, but plenty of power.

twentyfootdaredevil · Apr 24, 2013

I am interested. What injectors would you suggest with this modded turbo?

Could you pm me a price to have my turbo modded by you?

OldschoolPSD · Apr 24, 2013

The install is **** simple. If you don't want to do it I'm sure you could get just about any local shop to do the install. Pulling the turbo is the hard part, modding it is gravy.

IMHO its definately not worth pulling the turbo and sending it away. If you can pull the turbo yourself then you can definately install the new gear into the turbo.

twentyfootdaredevil · Apr 24, 2013

Fair enough. Where do I buy the kit?

NRHX2009 · Apr 24, 2013

email replied twentyfootdaredevil

twentyfootdaredevil · Apr 24, 2013

Thank you sir, can't wait to get this turbo installed!

NRHX2009 · Apr 25, 2013

Here is a Dyno Sheet. Specs:

E99 6pd 233K, 175/80's, t500, full fuel system, My 66mm turbo with 1.00 A/R non wastegated turbine housing

Billet wheel made the same Peak power as the cast, but made more power sooner in the rpm range. More power over the cast version of the 66mm wheel up until 2600rpm.
View attachment dyno66mm.pdf

fordman2121 · Apr 28, 2013

What did this truck put down on stock charger? 325 ish guessing. If so that's a nice increase even if it was 350 that's still 25 horse.

Tim @ P.I.S. · Apr 28, 2013

Nice curves.

And the fact that you made an extra 80ft lbs at 2250rpm is very nice.

NRHX2009 · Apr 28, 2013

Didnt dyno stock charger yet, hopefully this week i can get some more dyno time.

QUOTE=fordman2121;662408]What did this truck put down on stock charger? 325 ish guessing. If so that's a nice increase even if it was 350 that's still 25 horse.[/QUOTE]

S