Recent content by pt_ranger_v8

  1. P

    Pulling a ZF6

    I always pull the t-case when pulling a tranny - that extra 70-80 pounds makes handling the tranny awkward (as you've noticed!). A ratchet wrench is a must for the tcase bolts - should be a 14mm I think. They don't have to be super tight or anything, but there's not a lot of room under the...
  2. P

    Is this thing really needed and what does it do?

    If you have an e-vacumn pump, you need some way to store vacumn. The reason it's there with a belt-run pulley is because they suck ( haha) at low rpm's. You probably don't need it. Wouldn't hurt to leave it, either. :D
  3. P

    Looking for specifics - 33gal bronco tank

    Perfect. Thanks! :blitzed:
  4. P

    Looking for specifics - 33gal bronco tank

    Why pass on the bronco tank? I would think poly would be better than steel, hanging way down there on an OBS, at the end of an 8' bed. :shrug: Though, the extra 5 gals, and ~$10-20 cheaper isn't a bad thing at all. Cause if you're filling a 33-38 gallon tank at the pump, you're gonna use all...
  5. P

    Crew cab fab - my 95 build

    Nothing fancy in here. :flipa: This truck originally started life as a 351/c6 cclb, and it sucked:wtf:. Previous owner had a ~4" lift on it, blocks in the rear, shackle reverse/drop front hangar bracket up front. He also did some ghetto rehab inside, and swapped beds. After driving it for a...
  6. P

    Parting A 95 F250 Ext Cab 4X4 With A D60

    Still have the wiring harness from the engine to computer/idm? Also looking for tyranny wiring harness. Located at 73049.
  7. P

    1996 7.3 Parts

    How much for the engine harness to 73049?
  8. P

    high idle?

    Since it's Saturday, and I'm bored, I'm reading through the 'Features Description Service Features' manual for 94-98 Ford trucks, and the Engine oil temp below 50*C (122*F) will make the PCM up-idle to a maximum of 900 rpm. So, apparently, the OBS trucks STOCK have a high idle feature. (it's...
  9. P

    anyone seen a 7.3 oil cooler physically crack?

    I've had the front mount crack on my idi (same design) - puking nice green coolant all over the parking lot. Loved the phone call from the wife on that one :shocked: :doh:
  10. P

    Redhead Steering Box Installation

    Just got mine in - this install post confirmed how easy it is to put in. Redoing my PS cooler, then going for a test drive.
  11. P

    eseries swap into a 95 ??

    Not really. Again, this truck has already had one drivetrain swap. This is simply swap number two. :pint: I mean, there's no problems a welder, a sawzall, and some :pint: can't figure out :D Glad to hear about that though :)
  12. P

    eseries swap into a 95 ??

    Heh. That's me ;) Not entirely concerned about belt layouts, though that's good to know. What's different about the valve covers? Intake shouldn't matter - they body I have isn't' very stock anyway :naughty:. As long as the intake points toward the DS fender area, I can make something work...
See more

Random media

photo_7_5
Picture_170
Front End
Lifetime warranty
rear view
Batmo_versus_Stock
Gutted interior
35
IMAG0028
449D49D7-F1F3-4D00-959A-19155E78D0B0
IMG_3517_1_
IMAG1090

Latest posts

Members online

Total: 502 (members: 5, guests: 497)
Top