Ezlynk shows us a sneak peak.

Justin@DP-Tuner · Aug 10, 2016

Here is how Jody mounts his...

Using this mount...

https://www.amazon.com/iKross-Cellp...d=1470857328&sr=8-1&keywords=ikross+car+mount

ncollins64 · Aug 10, 2016

I actually like that mount. Thanks

Justin@DP-Tuner · Aug 10, 2016

ncollins64 said:
I actually like that mount. Thanks

No problem!

Jrs6.7 · Aug 10, 2016

Any news if it will allow tire size change and gear change ?

Strictly Diesel · Aug 11, 2016

My understanding is that Tire Size and TPMS changes are 'coming soon'.

Jrs6.7 · Aug 11, 2016

So no adjustability for gear changes ?

Strictly Diesel · Aug 11, 2016

Not usually required in a Ford because the speed sensor reads a tone ring on the ring gear. Ratio doesn't matter at that location, just tire size.

Jrs6.7 · Aug 11, 2016

Ok thanks!

c63 AMG · Aug 14, 2016

Lost of options with this mount and it's about $6.

Sent from my iPhone using Tapatalk

oli6578 · Aug 15, 2016

How did you mount the one on the sunglasses holder?

Sent from my iPhone using Tapatalk

c63 AMG · Aug 15, 2016

oli6578 said:
How did you mount the one on the sunglasses holder?

Sent from my iPhone using Tapatalk

Same mount as in the first pic just clips on.

Sent from my iPhone using Tapatalk

Jrs6.7 · Aug 15, 2016

Where did you get that mount c63?

c63 AMG · Aug 15, 2016

Tech Matte on Amazon

Sent from my iPhone using Tapatalk

valvetick · Sep 12, 2016

ImAti0n said:
So you use a stock EGT sensor from the exhaust and the Ez lynk can read it? What does the sensor plug into?

I'm currently running the sct livewire with the sct pyro in the EGR block off plate.

Has anyone answered this? I am looking at running this but want to be able to monitor egt's as well. Or is it possible to throw on a splitter and run a cts2 to monitor and only connect your phone to switch tunes?

Ikyo · Sep 14, 2016

I replaced the stock sensor with one from the exhaust and the EZ Lynk reads it just fine. Plugs into the factory location.

oli6578 · Sep 14, 2016

Ikyo said:
I replaced the stock sensor with one from the exhaust and the EZ Lynk reads it just fine. Plugs into the factory location.

I'm running PPEI *** on tune until my ****** pipe comes in and it reads egt temps now. Once ******d I have to run EGR blocker plates and use probe from exhaust. Correct? Where does probe plug into?

Sent from my iPhone using Tapatalk

valvetick · Sep 14, 2016

oli6578 said:
I'm running PPEI *** on tune until my ****** pipe comes in and it reads egt temps now. Once ******d I have to run EGR blocker plates and use probe from exhaust. Correct? Where does probe plug into?

Sent from my iPhone using Tapatalk

2nd that haven't looked yet but are the wires long enough to plug it back in once you move the probe from the exhaust into the ****** plate? Any other option to use something to monitor other then your iPhone or iPad?

Sent from my iPhone using Tapatalk

bigrpowr · Sep 14, 2016

valvetick said:
2nd that haven't looked yet but are the wires long enough to plug it back in once you move the probe from the exhaust into the ****** plate? Any other option to use something to monitor other then your iPhone or iPad?

Sent from my iPhone using Tapatalk

yeah the wires are long enough and once on a diet , yes you'll need at minimum a blockoff kit or full removal . then just use a sensor from the exhaust .