Search results

After replacing many 7.3 cam sensors and spending dozens of hours on a 7.3 with some issues that ended up being cured with this cam sensor i am convinced that this is the best one available. Definitely better than oem or napa brand anyway.... The gray BWD sensor from Advanced has a much...

$650 obo. Used but the truck it came off of was returned to stock so you just need the $250 vin liscense.

I was chasing a cylinder 3 contribution code that would sometimes move to cylinder 5 and loud slightly rough idle on a 7.3 after a engine rebuild and new injectors and finally got it fixed. I ohmmed the wiring, swapped injectors around, put in 2 new cam sensors from Ford, did a cranking and...

I am rebuilding a built trans and am trying to decide whether it has a billet input or not. The shaft has 4506 stamped on the end away from the converter. Google leads me to believe that it is a sonnax 300m billet input. Can anyone verify?

Just fuel in the oil from regens?

Got a 6.4 in the shop that was rebuilt last year by another shop. It has major coolant in the oil. Cracked block right? By my thinking that's the only way they can mix and not get oil in the coolant..

A guy trying to get home to Florida after deployment in the Army broke down yesterday in PA and i got him going again. Well now he’s stranded on the side of the road about 30 minutes outside of *******burg with a high-pressure oil system issue. Any members or good shops nearby?

This engine spun a main bearing and i am parting it all out. I pulled the heads and cam because i thought it had dropped a lifter and they are good. I have everything except for the injectors as i already sold them. Lmk what you need and i will get you a price! Located in Hagerstown MD. I would...

I have a 2001 super duty here I just put a 94 short block in. I switched everything including the front cover and pickup tube over and now the truck has a rough idle and miss while driving. Contribution and buzz test come back good but I suspect injectors anyway as it had coolant in the oil but...

What could cause that? The truck is basically stock and the last shop put a new oil cooler on it for the oil and coolant mixing issue which did not fix it. The only thing i could think of is a cracked block???

Full set of 8, only 31,000 miles but I cant gaurentee if they are good or not so im selling them as cores. $650 shipped.

I am selling my 2003 Ford Excursion Limited. It is black, 4wd 153,000 miles. It has a 31,000 mile 03 engine installed that I studded and deleted. No known issues with it at all other than paint peeling on the roof and front bumper but they will be repainted before selling. I am asking $16,500 obo.

I have a 03 6.0 that I'm diagnosing a crank no start issue on. I have proper ICP, fuel pressure, and FICM voltage. However I am getting no ficm sync and a cam sensor code. My research shows that the cam sensor code can be caused by a extended crank so I'm not too bothered by that however i did...

Is there any way to do this? I have a 04 excursion I just put a engine in and I want to start it to check for oil leaks and stuff before putting the trans back in. Can I just jump the starter?

I'm pulling the trans in a 04 excursion and am having a terrible time getting the torque converter unbolted. I'm going through the bottom bellhousing slot and its tight to begin with but the real problem is the slot and the nuts don't line up. I'm having to use a crowsfoot to break them loose...

Anyone have a used set laying around that they upgraded to h-11s or extreme studs? Got one I want to stud on the cheap.

We have a 04 excursion in the shop right now for a no start that has us stumped. It died while driving and was towed in. My coworker checked it and and found it had low ICP so he pulled the valve covers and checked the HPO system for leaks. There were none and the IPR works perfectly so he...

I have a set of brand new 6.7 fuel lines from a engine job I did that we ended up with 2 sets.

What the title says, LMK what you have. Looking to buy asap because the engine is at the machine shop already.

I am in need of a 6.7 DPF temporarily and am not having any luck rounding one up. If anyone near Hagerstown, MD has one I could borrow shoot me a pm. Thanks!